User manual DAIHATSU F300 SERVICE MANUAL

[. . . ] Some or all of these may be located behind or under the mounting surface. BassLink T has been designed for easy installation in many vehicle applications. BassLink T should be secured to a solid mounting surface using the supplied mounting hardware. BassLink T should be secured using a minimum of four screws along the different edges. BassLink T in an SUV cargo area. 2 MOUNTING F300 (CONTINUED) ROUTING THE WIRES All signal and power wires should be routed through the opening provided at the rear of the connection panel. [. . . ] · Install a fuse holder with a 25 A fuse within 18" of the battery's positive (+) terminal (see Figure 7). · The REM connection requires +5 to +12 Vdc signal to turn on BassLink T. Most head units with preamp outputs provide this remote voltage signal. For speaker-level applications, a remote connection is preferred but not required, since BassLink T's Auto Turn-On feature will sense voltage on the speaker wires to automatically turn on BassLink T. BassLink T (Control Panel) POWER LINE LEVEL INPUT HIGH LEVEL INPUT + L ­ REM GND REMOTE LEVEL CONTROL L R + R ­ ADDITIONAL MOUNTING FEET If your particular application inhibits the ability to secure the lower portion of BassLink T, please use the supplied mounting feet. They slide into the channels on the bottom of the unit and snap in place. This will give you the ability to secure BassLink T to the floor of your vehicle. BassLink T installation with optional feet. IMPORTANT: To enable BassLink T's Auto Turn-On feature, set the AUTO TURN-ON switch to the AUTO position (see Figure 13 on page 7). 3 APPLICATIONS BassLink T is equipped with two line-level (RCA) inputs and two speaker-level inputs. To help you plan your installation, we have included two system applications in Figures 8 and 9 on pages 4 and 5. BassLink T audio connections for a head unit with two line-level or subwoofer (RCA) outputs. POWER LINE LEVEL INPUT HIGH LEVEL INPUT + L ­ + R ­ AUTO TURN ON GAIN OFF AUTO BASS CROSSOVER BOOST FUSE 25A +BATT REM GND REMOTE LEVEL CONTROL PHASE L R 0° 180° 4 APPLICATIONS (CONTINUED) Figure 9. BassLink T audio connections for a head unit equipped with two speaker-level outputs. POWER LINE LEVEL INPUT HIGH LEVEL INPUT + L ­ + R ­ AUTO TURN ON GAIN OFF AUTO BASS CROSSOVER BOOST FUSE 25A +BATT REM GND REMOTE LEVEL CONTROL PHASE L R 0° 180° 5 INSTALLATION The Remote Level Control may be mounted under the dash or may be dismantled and mounted in the dash for a factory appearance. Unplug the RJ11 cable that connects the Remote Level Control to BassLink T. Make sure the head unit is off and its volume control is set to minimum. On BassLink T's top panel, initially set all controls to their midpoint positions, as shown in Figure 13. Turn on the head unit and play a favorite music track that has substantial bass. Set the head unit's volume control to 75 percent of the total output (approximately 3 o'clock on rotary controls). Adjust the GAIN control clockwise until the PEAK LED (on BassLink T's top panel) begins to flash with each bass note but doesn't stay lit continuously. Listen to your system, making a mental note of the amount of upper bass being reproduced. Switch the PHASE control to 180° and listen again for upper bass content. The position that provides the most upper bass is correct, but choose either setting according to your taste. Adjust the CROSSOVER control clockwise or counterclockwise until you hear only lowfrequency information. For example, you should NOT hear any vocals coming from BassLink T when seated in the normal listening position. [. . . ] · PROBLEM: No output from BassLink T when head-unit fader control is set to front or rear. · PROBLEM: BassLink T turns on before head unit is completely on and produces a "thump" sound. CAUSE and SOLUTION: For speaker-level connections, BassLink T is receiving a false turn-on signal. On BassLink T's top panel, slide AUTO TURN-ON to OFF and use the Remote (REM) connection. [. . . ]