User manual DAHON SINGLE DIGIT 7-TI

[. . . ] BRAKE INSTALLATION IMPORTANT! Only levers designated for direct-pull ® brakes such as the Speed Dial ® Ultimate, Speed Dial Ti, 7, 5 and AD3 ® levers can be used with Single Digit brakes. If you have any questions concerning compatibility of levers and brakes, contact your professional bike dealer. TM 1 MOUNT THE BRAKE Brake bosses must be clean and free of debris. Tighten the mounting bolt. 2 CHECK THE PAD SPACING Check that the brake arms are approximately parallel when the brake pads are on the rim. [. . . ] To reduce the possibility of an accident and minimize trail erosion, you should avoid locking-up your wheels. 3 ALIGN THE PADS Next, adjust the brake pad to be parallel with the rim. The top of pad should be at 1mm below the top of the rim. 4 TIGHTEN THE PADS With the pads aligned properly and flat against the rim, tighten the fixing nut to the specified torque. 5 INSTALL THE BOOT Insert the boot over the first lip of the noodle. The Avid noodle & boot are designed to be removed from the link without having to disengage the boot. 1mm CORRECT INCORRECT Tighten Pad Fixing Nut to: 6 - 8 Nm (52 - 69 in lb) 11D7/Ti-02/02 6 ANCHOR THE CABLE Pull the cable tight enough to have clearance of 1 - 1. 5mm, per side, between the rim and the brake pads. Tighten the cable anchor bolt to the specified torque. Tighten Cable Anchor Bolt to: 7 CENTER THE BRAKE Center the brake by adjusting the spring tension adjusters. Turn each spring adjuster screw with a 3mm hex wrench clockwise to increase spring tension. 8 TEST THE SYSTEM With two fingers, squeeze the brake lever firmly about a dozen times to ensure the cables are seated properly and operate smoothly. Re-torque if necessary. Tighten Cable Anchor Bolt to: LIMITED WARRANTY Avid, LLC (Avid) warrants to the original consumer purchaser of every Avid product that the product shall be free from defects in workmanship and materials for a period of one (1) year from the original date of purchase. The sole remedy under this warranty is limited to, at Avid's sole discretion, repair or replacement of the defective product. This warranty only applies to the original consumer purchaser and is not transferable. THIS WARRANTY DOES NOT COVER normal wear and tear (including, without limitation, brake pad wear), or defects or failures that are related in any way to improper installation or follow-up maintenance, accident, abuse or neglect (including, without limitation, thread damage). Since Avid has no control over the product's final use, Avid also does not warrant the suitability of the product for specific riders and/or uses. IN NO EVENT SHALL AVID BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT OR PRODUCTS LIABILITY, INCLUDING WITHOUT LIMITATION, PERSONAL INJURY DAMAGES, PROPERTY DAMAGE OR ECONOMIC LOSSES. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. ALL IMPLIED WARRANTIES, INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY LIMITED TO THE ONE (1) YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. [. . . ] If you have any question about their condition, consult your bicycle dealer or replace them. 3mm 4mm 2. Slide the new brake pad in ALL THE WAY until it is fully aligned with the forward edge of the brake pad holder. Push the locking pin in until it is fully engaged. 5mm 6mm Avid, LLC 2875 W Oxford Ave # 7 Englewood, CO 80110 USA tel 303. 762. 9353 fax 303. 762. 1133 Website: www. avidbike. com Email: tech@avidbike. com Avid, Single Digit and Rim Wrangler are trademarks of Avid, LLC [. . . ]