User manual DAHON I-MOTION 3

[. . . ] Special advice to assist in the better handling of the operation, control, and adjustment procedures. © Copyright SRAM Corporation 2006 Publ. Released June 2006 SRAM Technical Documentation, Schweinfurt/Germany 2 i-MOTION 3 · June 2006 TA B L E O F C O N T E N T S E THE SRAM i-MOTION 3 SYSTEM 4 OPERATION 5 MAINTENANCE AND CARE » Gear adjustment » Remove and fit rear wheel » Cleaning and lubrication » Repair work / wear parts 6 7 10 11 A S S E M B LY O F C O M P O N E N T S 12 TECHNICAL DATA 18 i-MOTION 3 · June 2006 3 THE SRAM i-MOTION 3 SYSTEM A modern bicycle derailleur should be sporty, load shiftable, intuitive to use and durable!With the new i-MOTION 3, SRAM delivers an internal gear hub that meets and exceeds all these requirements! i-MOTION 3 gear hub Load shiftable. [. . . ] » During the winter season, you should clean your bicycle in shorter intervals so that winter road salt cannot cause any damage. Do not oil chain until completely dry. LUBRICATION » The rear wheel hub is provided with permanent lubrication and maintenance-free under normal conditions. » Regular lubrication will extend the chain's service life. 10 i-MOTION 3 · June 2006 MAINTENANCE AND CARE REPAIR WORK / WEAR PARTS REPAIR WORK Only a qualified bike dealer should perform any necessary work on the gear hub, shifter, and brakes. » Unauthorized work on your i-MOTION 3 system could endanger you and your warranty may become void. » Please contact your qualified bike dealer regarding any questions or problem you may have. Back pedal brake If the back pedal brake is braking too hard, the brake jacket has to be lubricated with special grease. Cable Change If a cable must be replaced (shifter cable or brake cable), contact your qualified dealer. WEAR PARTS Brake liners or brake jackets, brake cables, shift cables, handlebar grips, sprockets, and bike chains are wear parts. Please check these parts regularly and replace them timely. E i-MOTION 3 · June 2006 11 A S S E M B LY OF COMPONENTS A S S E M B LY H U B » Spoke the hub as normal. The curve must point to the outside. 17 driver. Set the sprocket (2) onto the If an offset sprocket will be used, mount the sprocket with the curve pointing to the outside. 17 2 18 ring (3) onto the driver. Check proper seat of the retaining ring. Mount the sprocket retaining 19 onto the axle end of the Slide the cable stop bracket (4) 18 3 sprocket side. Thereafter mount the washer with rubber insert (5) to fix the the cable stop bracket. » Place the rear wheel into the rear frame. 19 4 5 12 i-MOTION 3 · June 2006 A S S E M B LY OF COMPONENTS 20 each (6) onto each axle end. The serrations of the retaining washer must bear against the dropout of the frame. Align the stop 21 parallel tocableframebracket (7) the stay (8). Slide one retaining washer 20 6 E 22 tighten them alternately with a torque of 30 ­ 40 Nm (266 ­ 350 in. lbs. ). Mount the axle nuts (9) and 21 7 23 lever (10) between the two If applicable, mount the brake 8 straps of the frame clamp (11). Tightening torque: 2 ­ 3 Nm (18 ­ 27 in. lbs. ). 22 9 23 11 10 i-MOTION 3 · June 2006 13 A S S E M B LY OF COMPONENTS A S S E M B LY S H I F T E R 24 handlebar. Slide the shifter (1) onto the 24 25 onto the handlebar. [. . . ] to 1/2 OLD /2" x 1/8" and 1/2" x 3/32" 16 / 17 / 18 T. (off-set) SRAM i-MOTION 3 not suitable for tandems and transport bicycles i-MOTION 3 shifter SHIFTER Shifter type Assembly location Gear indication Barrel adjuster Clamp diameter Straight handlebar ends Cable laying Twist shifter Right side of handlebar Window Indexed 22. 3 mm Length = min. 150 mm Continuous cable housing (pre-assembled) i-MOTION 3 · June 2006 18 Version with back pedal brake Ø 7. 3 124. 5 CL straight A A M 10x1 3 1 T E C H N I C A L D ATA M 10x1 i-MOTION 3 · June 2006 F2 19 HR 78 3 F1 100 / 2 OLD 2. 8 CL off-set 2. 8 Ø 3. 0 OLD L 19 E WORLD HEADQUARTERS Chicago, Illinois U. S. A. [. . . ]