User manual DAHON ANDROS 2010

[. . . ] · There are two different types of reinforced connecting pins available. If connecting pins other than reinforced connecting pins are used, or if a reinforced connecting pin or tool which is not suitable for the type of chain is used, sufficient connection force may not be obtained, which could cause the chain to break or fall off. Chain 9-speed super narrow chain such as CN-7701 / CN-HG93 8- / 7- / 6-speed narrow chain such as CN-HG50 / CN-IG51 Reinforced connecting pin Silver 6. 5mm Technical Service Instructions SI-5VX0A Rear Derailleur Stroke adjustment and cable securing 1. Top adjustment Turn the top adjustment screw to adjust so that the guide pulley is below the outer line of the smallest sprocket when looking from the rear. Outer line of smallest sprocket 5. [. . . ] Top adjustment Turn the top adjustment screw to adjust so that the guide pulley is below the outer line of the smallest sprocket when looking from the rear. Outer line of smallest sprocket 5. SIS Adjustment Operate the shifting lever several times to move the chain to the 2nd sprocket. Then, while pressing the lever just enough to take up the play in the lever, turn the crank arm. Play 3 2 RD-4500 1 2 Lever (A) In order to realize the best performance, we recommend that the following combination be used. Series Shifting lever TIAGRA ST-4500 / R600 / 5510 / 6510 ST-4500 / R600 / 5510 / 6510 SL-7710 / R440 / R660 / BS77 SL-R440 / R650 18 SIS-SP41 RD-4500-SS SS FH-4500 CS-HG50-9 CN-HG53 SM-SP17 RD-4500-GS GS 27 1 Guide pulley Top adjustment screw 2 When shifting to 3rd When no sound at all is heard Chain tool TL-CN32 / TL-CN24 TL-CN32 / TL-CN24 Gears Outer casing Rear derailleur Type Freehub Cassette sprocket Chain Bottom bracket cable guide 2. Connection and securing of the cable Connect the cable to the rear derailleur and, after taking up the initial slack in the cable, re-secure to the rear derailleur as shown in the illustration. Tightening torque: 5 - 7 N·m {44 - 60 in. lbs. } Pull Black 7. 1mm · If it is necessary to adjust the length of the chain due to a change in the number of sprocket teeth, make the cut at some other place than the place where the chain has been Reinforced Connecting Pin joined using a reinforced connecting pin or an end pin. The chain will be damaged if it is cut at a place where it has been joined with a reinforced End Pin Link Pin connecting pin or an end pin. · Check that the tension of the chain is correct and that the chain is not damaged. · For smooth operation, use the specified outer casing and the bottom bracket cable guide. · Grease the inner cable and the inside of the outer casing before use to ensure that they slide properly. · Use a frame with internal cable routing is strongly discouraged as it has tendencies to impair the SIS shifting function due to its high cable resistance. · Parts are not guaranteed against natural wear or deterioration resulting from normal use. · For maximum performance we highly recommend Shimano lubricants and maintenance products. · For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a professional bicycle dealer. Installation of the rear derailleur When installing, be careful that deformation is not caused by the B-tension adjustment screw coming into contact with the dropout tab. Bracket spindle tightening torque: 8 - 10 N·m {70 - 86 in. lbs. } Largest sprocket Guide pulley 1 2 1 2 5 mm Allen key Low adjustment screw B-tension adjustment screw 4. How to use the B-tension adjustment screw Dropout tab Mount the chain on the smallest chainring and the largest sprocket, and turn the crank arm backward. [. . . ] lbs. } Largest sprocket Guide pulley 1 2 1 2 5 mm Allen key Low adjustment screw B-tension adjustment screw 4. How to use the B-tension adjustment screw Dropout tab Mount the chain on the smallest chainring and the largest sprocket, and turn the crank arm backward. Then turn the B-tension adjustment screw to adjust the guide pulley as close to the sprocket as possible but not so close that it touches. [. . . ]