User manual DAHON 26AXS 2010

[. . . ] lbs. } Note · For smooth operation, use the specified outer casing and bottom bracket cable guide. · Grease the inner cable and the inside of the outer casing before use to ensure that they slide properly. · Use a frame with internal cable routing is strongly discouraged as it has tendencies to impair the SIS shifting function due to its high cable resistance. · Operation of the levers related to gear shifting should be made only when the front chainwheel is turning. [. . . ] · Use an outer casing which still has some length to spare even when the handlebars are turned all the way to both sides. Furthermore, check that the shifting lever does not touch the bicycle frame when the handlebars are turned all the way. · A special grease is used for the gear shifting cable (SIS-SP41). Do not use DURA-ACE grease or other types of grease, otherwise they may cause deterioration in gear shifting performance. · Do not disassemble the indicator and shifting lever unit, as this may damage them or cause mis-operation. · Parts are not guaranteed against natural wear or deterioration resulting from normal use. · For maximum performance we highly recommend Shimano lubricants and maintenance products. · For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a professional bicycle dealer. Gear shifting operation Both lever (A) and lever (B) always return to the initial position when they are released after shifting. When operating one of the levers, always be sure to turn the crank arm at the same time. 2. : from 3rd to 6th 6 3 When lever (B) is operated, there is one click where trimming (the noise prevention mechanism) engages, and a second stronger click when the gear shift stroke is completed. After trimming, the next push will complete the gear shift stroke. Gear shift complete stroke Click Trim operation Click To shift from a large sprocket to a smaller sprocket Press lever (B) once to shift one step from a larger to a smaller sprocket. Shifting lever mounting screws Shifting lever mounting screws Lever (B) Lever (B) 4. To assemble, align the shifting lever unit and the brake lever bracket and then secure the shifting lever mounting screws. To assemble, align the shifting lever unit and the brake lever bracket and then secure the shifting lever mounting screws. Carry out steps 3 - 4 for replacement of the indicator. Shifting lever Outer casing Gears Front derailleur Front chainwheel Bottom bracket Rear derailleur Freehub Cassette sprocket Chain Bottom bracket cable guide F : SL-R441 R : SL-R440 27 Trimming (noise prevention operation) If the chain is on the large front chainwheel and the larger rear sprocket, the chain will rub in the front derailleur plate, producing a characteristic noise. When this happens, press lever (B) lightly (to the point where it clicks); this causes the front derailleur to move slightly towards the smaller chainwheel, thereby eliminating the noise. Chain position 5. Carry out steps 3 - 4 for replacement of the indicator. SP41 FD-R443 / FD-R453 FC-4404 / FC-4503 BB-ES51/30 / SM-FC4500 RD-4400 / RD-4500 FH-4400 / FH-4500 CS-HG50-9 CN-HG53 SM-SP17 Installing the shifting cable Cutting the outer casing When cutting the outer casing, cut the opposite end to the end with the marking. After cutting the outer casing, make the end round so that the inside of the hole has a uniform diameter. Movement of the front derailleur Outer end cap Installing the inner cable < Front > Operate lever (B) two times or more, and check on the indicator that the lever is at the lowest position. Then remove the inner hole cover and connect the inner cable. Tightening torque: 5 - 7 N·m {44 - 60 in. [. . . ] Then remove the inner hole cover and connect the inner cable. Tightening torque: 5 - 7 N·m {44 - 60 in. lbs. } Inner cable Inner hole cover Lever (B) Installing the inner cable < Rear > Operate lever (B) eight times or more, and check on the indicator that the lever is at the highest position. Then remove the inner hole cover and connect the inner cable. Tightening torque : 5 - 7 N·m {44 - 60 in. lbs. } Inner cable Inner hole cover Lever (B) This service instruction explains how to use and maintain the Shimano bicycle parts which have been used on your new bicycle. [. . . ]