User manual DAELIM S2 BROCHURE

[. . . ] The photographs and drawings shown in this manual may differ from those of actual vehicles due to changes in vehicle specifications and modifications made. This vehicle is designed for 2 riders including the operator. SAFETY PRECAUTIONS Careful driving and the wearing of proper attire and safety equipment are the most important factors in the safe operation of the scooter. Many new vehicle owners operate their newly purchased vehicles with great care and attention to safety factors. However, after becoming accustomed to the operations are often discarded, which can lead to accidents. [. . . ] If the tail light is off while driving at night, it will cause an accident by failure of notice by the other drivers. Check the condition daily. <INSPECTION OF STOP LAMP> Turn a main switch "ON". Check a stop lamp for proper operation by operating the front wheel and the rear wheel brakes, and also a lens for damage or contamination. <HEADLIGHT BULB> (1) Loosen 4 special screws and remove the front cover. (3) Loosen 2 washer bolts and 9 tapping screws, and then disassemble the front under cover. BULB REPLACEMENT METHOD Be sure to turn a main switch "OFF" prior to replacement of a bulb. After replacement with new bulb, check for proper operation. CAUTION Care is to be taken to avoid leaving fingerprints on a headlight bulb. Failing to observe this may cause early damage of the headlight bulb resulted from concentration of heat. If touched to it with bare hands, clean it with a cloth soaked with alcohol to prevent from early damage. <INSPECTION OF WINKER> Turn a main switch "ON". Check the lamp for proper operation (front/rear and right/left) and sound by operating the switch, and also a lens for damage or contamination. 28 (4) Disassemble a headlight socket by pulling it out. (6) Loosen the steel wire, and disassemble the head light bulb. HEADLIGHT BULB: 12V 55W(H7) <HEADLIGHT LUMINATION ANGLE> Adjust headlight lumination angle by turning an adjusting bolt on a headlight. (Use type screwdriver. ) (1) Adjust the upper/lower by turning the screw on outside. (2) Adjust the right/left by turning the screw on inside. <TAIL/STOP LIGHT BULB> (1) Loosen 2 tapping screws to disassemble tail light lens. There are no adjustments to perform, but fluid level and pad wear must be inspected periodically. The system must be inspected frequently to ensure there are no fluid leaks. If the lever free play becomes excessive and the brake pads are not worn beyond the recommended limit, there is probably air in the brake system and it must be bled. See your authorized Daelim dealer for this service. WARNING If your motorcycle is overturned or involved in a collision, inspect control levers, cables, brake hoses, calipers, accessories, and other vital parts for damage. Have your authorized Daelim dealer inspect the major components, including frame, suspension and steering parts, for misalignment and damage that you may not be able to detect. Use new, genuine Daelim parts or their equivalent for maintenance and repair. Parts which are not of equivalent quality may impair the safety of your motorcycle and the effective operation of the emission control systems. CAUTION Brake fluid may cause irritation. In case of contact, flush throughly with water and can a doctor if your eyes were exposed. Keep out of reach of children. 34 <REPLENISHING FRONT BRAKE FLUID> Check that the fluid level is above the LOWER level mark with the motorcycle in an upright position. Brake fluid must be added to the reservoir whenever the fluid level begins to reach the LOWER level mark. Clean dust and other foreign materials around reserve tank to prevent foreign materials from falling inside tank. [. . . ] <FRAME NUMBER> <ENGINE NUMBER> 48 SAFE DRIVING PREPARATION BEFORE DRIVING Performing daily inspection Putting on the protective gears (Helmet, glove, goggles, etc. ) Bringing the driver's licence Determinating the path to the desired destination ING RM RFO ILY N PE DA TIO PEC INS R'S IVE DR ENCE LIC PR FU OT EL GE ECT , AR IV SE 49 DRIVING METHOD DRIVING POSITION The appropriate driving position is most important thing to driving safely. Arms : Relieve the tension and bend arms to inside and let them act as the spring. Hands : Grip the handle the position away from the inside end of the handle with distance of one finger to facilitate the operation of the switch and lever. Wrist : Keep the state to act freely without applying excessive force to the shoulder and arms. [. . . ]