User manual D-LINK GO-DSL-N150

[. . . ] Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1 1. 2 1. 3 1. 4 2 3 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 LEDs and Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If data packets include the MAC address, the data packets are placed into the group. If data packets include the IP address, the data packets are placed into the group. Select this option to Activated/Deactivated the 4094 VID on the 4 different queues. VID (VLAN ID) is the identification of the VLAN, which is basically used by the Vlan ID Range standard 802. 1Q. Of the 4096 possible VIDs, a VID of 0 is used to identify priority frames and value 4095 (FFF) is reserved, so the maximum possible VLAN configurations are 4, 094. IPP/DS Field IP Precedence When IPP/TOS is set, select the IP Precedence ranging from 0 to 7. Support application options such as IGMP, SIP, H. 323, MGCP, SNMP, DNS, DHCP, RIP, RSTP, RTCP and RTP. Description QoS, you may set the upload bandwidth of the WAN 37 GO-DSL-N150 User Manual Field Range Type of Service DSCP Range Select this option to Activate/Deactivated the 802. 1p. Although network managers must determine actual mappings, IEEE has made broad recommendations. Seven is the highest priority which is usually assigned to network-critical traffic such as Routing Information Protocol (RIP) and Open Shortest Path First (OSPF) table 802. 1p updates. Five and six are often for delay-sensitive applications such as interactive video and voice. Data classes four through one range from controlled-load applications such as streaming multimedia and business-critical traffic - carrying SAP data, for instance down to "loss eligible" traffic. Zero is used as a best-effort default priority, invoked automatically when no other value has been set. Support services including Normal service, Minimize delay, Maximize throughput, Maximize reliability and Minimize monetary cost. To view the rules and actions, click QoS Settings Summary to enter the page shown in the following figure appears. 38 GO-DSL-N150 User Manual 3. 5. 5 VLAN Choose Advanced Setup > VLAN, the page shown in the following figure appears. Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization. In the VLAN page, click Assign VLAN PVID for each Interface, and the page shown in the following figure appears. 39 GO-DSL-N150 User Manual The following table describes the parameters of this page: Field Description Each physical port has a default VID called PVID (Port PVID VID). PVID is assigned to untagged frames or priority tagged frames (frames with null (0) VID) received on this port. ATM VC # Ethernet Port # Wirelss LAN Next Assign the PVID to Wireless LAN. Assign the PVID to Ethernet Ports. In the VLAN page, click VLAN Group Setting, and the page shown in the following figure appears. 40 GO-DSL-N150 User Manual The following table describes the parameters of this page: Field VLAN Index Active VLAN ID ATM VCs Ethernet Wireless LAN Save Delete Cancel Click it to save the settings. Choose to assign the Wirless LAN to the VLAN group. 41 GO-DSL-N150 User Manual 3. 5. 6 ADSL Click Advanced Setup > ADSL, the page shown in the following figure appears. The ADSL feature can be selected when you meet the physical connection problem. [. . . ] In turn, a device can leave a network smoothly and automatically when it is no longer in use. Auto-Configure: UPnP network devices can automatically configure network addressing, announce their presence in the network to other UPnP devices and enable exchange of simple product and service descriptions. DDNS The Dynamic Domain Name System lets you use a static host name with a dynamic IP address. User should type the host name, user name and password assigned to your ADSL Router by your Dynamic DNS provider. User also can decide to turn on DYNDNS Wildcard or not. 3. 8. 5 Maintenance Choose Help > Maintenance, the page shown in the following figure appears. [. . . ]