User manual D-LINK DWL-3500 BROCHURE

[. . . ] D-Link Unified Access System User Manual FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CE Mark Warning This is a Class A product. [. . . ] Table 23 describes the fields on the new page. Power Performing Advanced Access Point Management 119 D-Link Unified Access System User Manual Enabling AP Debugging You can enable debugging on an AP to allow Telnet access to the access point. Once you Telnet to the AP, you can issue commands from the CLI to help you troubleshoot. The fields in Table 22 appear when you click the Debug link for a managed AP on the Managed AP Advanced page. Table 22. AP Debug Field MAC Address Location IP Address Status Description Shows the MAC address of the access point. Shows the location of the access point, as configured in the Valid AP database. Shows the debug status, which can be one of the following: · · · Password Confirm Password Enable Debug None--Debugging has not been enabled or disabled. Set Complete--Debugging has been enabled or disabled. Enter the admin password for the AP (the default is admin). Since the password is encrypted, you must retype the password to confirm the password. From the AP CLI, you can also access the standard Linux prompt by typing the '!' character. You can issue the following debug commands at the Linux OS prompt: · get management--Display management interface information · get managed-ap--Display managed AP information You can issue the following debug commands at the Linux OS prompt: · · ifconfig--display all interfaces. cat /proc/meminfo--View memory utilization Adjusting the Channel and Power Changes you make to the channel and power are runtime changes only. If you change the channel or power settings, the new settings are lost if the AP or switch is reset. The fields in Table 23 appear when you click the current channel or power setting for an AP on the Managed AP Advanced page. Table 23. Managed AP Channel/Power Adjust Field AP MAC Address Radio Description Shows the MAC address of the access point. The changes apply only to this radio. 120 © 2001- 2008 D-Link Corporation. All Rights Reserved. 6 Managing and Maintaining D-Link Access Points Table 23. Managed AP Channel/Power Adjust Field Channel Status Description The status is one of the following: · · · Channel None Set Requested Set Complete The Channel defines the portion of the radio spectrum that the radio uses for transmitting and receiving. The range of channels and the default channel are determined by the Mode of the radio interface. IEEE 802. 11b/802. 11g modes (802. 11 b/g) support use of channels 1 through 11 inclusive, while IEEE 802. 11a mode supports a larger set of nonconsecutive channels (36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165). NOTE: The available channels depends on the country in which the APs operate. NOTE: For radios that use 802. 11a mode, some countries have a regulatory domain that requires radar detection. For these countries (based on the country code setting), the radio automatically uses the 802. 11h protocol for selecting the channel if radar is detected on the statically assigned channel. [. . . ] All Rights Reserved. Technical Support Suporte Técnico Você pode encontrar atualizações de software e documentação de usuário no site da D-Link Brasil www. dlinkbrasil. com. br. A D-Link fornece suporte técnico gratuito para clientes no Brasil durante o período de vigência da garantia deste produto. Suporte Técnico para clientes no Brasil: Telefone São Paulo +11-2185-9301 Segunda à sexta Das 8h30 às 18h30 Demais Regiões do Brasil 0800 70 24 104 E-mail: e-mail: suporte@dlinkbrasil. com. br 263 D-Link Unified Access System User Manual 264 © 2001- 2008 D-Link Corporation. All Rights Reserved. Technical Support Dukungan Teknis Update perangkat lunak dan dokumentasi pengguna dapat diperoleh pada situs web D-Link. Dukungan Teknis untuk pelanggan: Dukungan Teknis D-Link melalui telepon: Tel: +62-21-3851275 Senin sampai Jumat 9:00 - 12:30, 14:00 - 18:00 Waktu Singapura Dukungan Teknis D-Link melalui Internet: e-mail: support@dlink. com. sg 265 D-Link Unified Access System User Manual 266 © 2001- 2008 D-Link Corporation. Herrmann Street Fountain Valley, CA 92708 TEL: 1-800-326-1688 URL: www. dlink. com Canada 2180 Winston Park Drive Oakville, Ontario, L6H 5W1 Canada TEL: 1-905-8295033 FAX: 1-905-8295223 URL: www. dlink. ca Europe (U. [. . . ]