User manual D-LINK DSR-250N

[. . . ] Building Networks for People Unified Services Router User Manual DSR-150 / 150N / 250 / 250N / 500 / 500N / 1000 / 1000N Ver. Th e man u fact u rer makes n o rep res ent at ions o r warran t ies wit h res p ect t o t h e co n t en t s h ereo f an d s p ecifically d is claim an y imp lied warran t ies o f merch an t ab ilit y o r fit n es s fo r an y p art icu lar p u rp o s e. Th e man u fact u rer res erv es t h e rig h t t o rev is e t h is p u b licat io n an d t o make ch an g es fro m t ime t o t ime in t h e co n t ent h ereof wit h o ut o b lig at ion o f t h e man u factu rer t o n o t ify an y p ers o n o f s u ch rev is io n o r ch an g es . 49 Figure 29: Load Balancing is available when multiple WAN ports are configured and Protocol Bindings have been defined . [. . . ] If you are using Internet Explorer, click Refresh to ensure that the Java applet is loaded. The factory default login name is admin and the password is password. When entering configuration settings, click Apply before moving to another menu or tab; otherwise your changes are lost. Your changes may have been made, but the browser may be caching the old configuration. 0 is shown, your firewall has not obtained an IP address from your ISP. When the modem LEDs indicate that it has resynchronized with the ISP, reapply power to the router. If the router still cannot obtain an ISP address, see the next symptom. Ask your ISP if it requires a login program — PPP over Ethernet (PPPoE) or some other type of login. If yes, verify that your configured login name and password are correct. If yes, select Network Configuration > WAN Settings > Ethernet ISP Settings and set the account name to the PC hostname of your ISP account. Ask your ISP if it allows only one Ethernet MAC address to connect to the Internet, and therefore checks for your PC’s MAC address. If yes, inform your ISP that you have bought a new network device, and ask them to use the firewall’s MAC address. Alternatively, select Network Configuration > WAN Settings > Ethernet ISP Settings and configure your router to spoof your PC’s MAC address. Ask your ISP for the addresses of its designated Domain Name System (DNS) servers. If you have just configured the router, wait at least 5 minutes, select Administration > Time Zone , and recheck the date and time. Select Administration > Time Zone and view the current date and time settings. Click to check or uncheck “Automatically adjust for Daylight Savings Time”, then click Apply. Type ping <IP_address> where <IP_address> is the router’s IP address. If the path is not working, Test the physical connections between PC and router  If t h e LA N p o rt LED is o ff, g o t o t h e “LED d is p lay s” s ectio n o n p age B 1 an d fo llo w in s t ru ct io n s fo r “LA N o r In t ern et p o rt LEDs are n o t lit . ”  Verify t h at t h e co rres p o n d in g lin k LEDs are lit fo r y o u r n et wo rk in t erface card an d fo r an y h u b p o r t s t h at are co n n ect ed t o y o u r wo rks t at io n an d firewall. If the path is still not up, test the network configuration:  Verify t h at t h e Et h ern et card d riv er s o ft ware an d TCP/ IP s o ft ware are in s t alled an d co n fig u red o n t h e PC. Type ping -n 10 <IP_address> where -n 10 specifies a maximu m of 10 tries and <IP address> is the IP address of a remote device such as your ISP’s DNS server. [. . . ] FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference th at may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. [. . . ]