User manual D-LINK DSL-504T

[. . . ] 27 DMZ setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Allow Incoming Ping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Setting unit to factory defaults by using the reset button. . . . . . . . . . 39 How to Firmware update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the pc has got a statically assigned IP address then you will need to change the address to an IP address in the same range as what the ISP has provided you. I. E If the ISP has given you 195. 74. 119. 177-180 then you can give the pc an IP address of 195. 74. 119. 178, set the gateway to the IP address of the router. Login Select setup connection 1 Page 9 D-Link Europe Limited UK Support Team DSL-504T Install Guides The name can be anything you like. Select the type of connection that you use from (PPPoE, PPPoA, Static, DHCP, Bridge, CLIP). As most ISP's in the UK are currently using PPPoA this document will concentrate on PPPoA configuration. UnTick the NAT and FIREWALL checkboxes PPP Settings Set encapsulation to VC Enter your Username and Password You do not need to change the Keep Alive and MAX Fail values from the default. You will need to change the MRU/MTU value depending on what the ISP can support. If you are having problems after connection i. e slow web browsing, check with the ISP what the MTU value should be. Then go to advanced Page 10 D-Link Europe Limited UK Support Team DSL-504T Install Guides And select the advanced security option. Untick the Enable firewall and NAT services box. Page 11 D-Link Europe Limited UK Support Team DSL-504T Install Guides Then go to the Status tab. Page 12 D-Link Europe Limited UK Support Team DSL-504T Install Guides Then click on Connection status. Under the Wan section it will show you your connection information. Your configuration is now complete and you should be able to browse the web. Then click on tools and system commands, you will get the below screen. Click on Save all, so that the configuration is saved on the unit. If you ever need to power off the Page 13 D-Link Europe Limited UK Support Team DSL-504T Install Guides unit then the configuration will come back. If you do not save the settings when the unit is powered of the settings will be lost. DSL-504T Port Forwarding. DSL-504T F/W-V1. 00B02T02. EN. 20040427 Web server--------DSL-504T-----------Internet----------PC 192. 168. 1. 2 192. 168. 1. 1(internal) 81. 107. 232. 201(external) For the pc to be able to access the web server you need redirect the port 80 for web traffic to the local IP address of the web server. So when the pc enters 81. 107. 232. 201 into the web browser the web site being hosted on 192. 168. 1. 2 is displayed. Page 14 D-Link Europe Limited UK Support Team DSL-504T Install Guides The default IP address for the router is 192. 168. 1. 1 Open up Internet explorer and enter the IP address of the router. You will be displayed with the below screen. The default USERNAME is admin and the PASSWORD is admin. You will then be displayed with the below screen Page 15 D-Link Europe Limited UK Support Team DSL-504T Install Guides Then Select the Advanced tab Select Port Forwarding. Page 16 D-Link Europe Limited UK Support Team DSL-504T Install Guides Choose an active connection and select the LAN IP of the server so in the above example 192. 168. 1. 2. Then Select servers and you will get the below screen. Page 17 D-Link Europe Limited UK Support Team DSL-504T Install Guides Select the web server and click on Add Click on apply. Then click on the port forwarding it will show the applied rules for the selected pc's. Page 18 D-Link Europe Limited UK Support Team DSL-504T Install Guides If you would like to forward other ports than the ones that are pre configured for you. You can use the User option. Select add Page 19 D-Link Europe Limited UK Support Team DSL-504T Install Guides The rule name can be anything. Port Start is the start port number in a range of ports Port end is the end port number in a range of ports If you need to redirect only one port then keep the start and end ports as the same. [. . . ] If you then click on access control you will see that the rule has been applied to the pc. The pc will not be able to use any service that uses port 210. Page 33 D-Link Europe Limited UK Support Team DSL-504T Install Guides DMZ setup Click on advanced and advanced Security Tick the enable DMZ and select the IP address of the pc that you need to put into the DMZ. The above shows that the pc with an IP address of 192. 168. 1. 2 is in the DMZ. Page 34 D-Link Europe Limited UK Support Team DSL-504T Install Guides Allow Incoming Ping By default the Incoming ping is blocked. And you will get the below screen Page 41 D-Link Europe Limited UK Support Team DSL-504T Install Guides Click on browse under the update gateway firmware. In the folder where the zip file is expanded you will get option for 2 files 1) Fs file 2) Kernel File Select The FS file then click on update gateway. Once the file has gone through and the unit has rebooted login again You now need to send the kernel file through Once the upgrade has finished the unit will reboot. [. . . ]