User manual D-LINK DSL-500T

[. . . ] DSL-500T ADSL Router User's Guide (February 2004) 651DSL500T01 DSL-500T DSL Router User's Guide FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] If this setting is not configured properly, the Router will not work. Figure 3-4. DSL Setup menu (change modulation type) If you are instructed by your ISP to change the Modulation type is used for your service, select the desired modulation type and then click Apply. By default, the Router will automatically detect the modulation used; this setting is listed as MMODE (Multi-mode). 18 DSL-500T ADSL Router User's Guide Configure Connection 1 for PPPoA PPP or Point-to-Point protocol is a standard method of establishing a network connection/session between networked devices. Different forms of PPP include PPPoA and PPPoE (discussed below) involve an authentication process that requires a username and password to gain access to the network. PPPoA (PPP over ATM) as described in RFC 2364, is a method of using PPP on an ATM network. ATM is used for many types of telecommunications services including ADSL. To configure the WAN connection for PPPoA, perform the steps listed below. Some of the settings do not need to be changed the first time the device is set up, but can be changed later if you choose. Figure 3- 5. PPPoA Connection 1 Setup menu To configure the default connection type (PPPoA) for Connection 1, follow the steps listed below. To change the connection type of Connection 1 to an alternative type follow the instructions according to the desired type as described below in Change the Connection Type. Click the Connection 1 button under WAN Setup to view the PPPoA Connection Setup menu pictured in the example above. Type in a Name for the connection or use the default name conn_1_PPPoA_8_35 in the space provided. Under Options, enable NAT and/or Firewall by selecting the corresponding selection box. If you are told to change the VPI or VCI values, type in the values given to you by your service provider. Leave the default QoS values if you are unsure or the ISP did not provide this information. If you are told to change these, type in the values given to you by your service provider. Type the Username and Password used to verify the identity of your account. Typically, the Username is an account number assigned by your ISP and appears in the form account#@serviceprovider. com, while the Password may have been chosen by the account holder. You are now finished changing setting for the primary WAN connection known as Connection 1. It is now necessary to save the changes you just made and restart the Router. 8. 19 DSL-500T ADSL Router User's Guide 9. To save the changes made to Connection 1, click the Tools tab and then click on the System Commands button. Look under WAN to view the State of Connection 1, it should read Connected. If the WAN connection state does not appear to Connected after a few minutes, go back to the Connection 1 Setup menu, check the settings and make sure they are correct. Change the Connection Type The default connection protocol used for the Router is Point-to-Point Protocol over ATM (PPPoA). [. . . ] Microfilters are easy-to-install, in-line devices, which attach to the telephone cable between the telephone and wall jack. A typical in-line microfilter installation is shown in the diagram below. Microfilter Installation Important: Do not install the microfilter between the Modem and the telephone jack. Microfilters are only intended for use with regular telephones, Fax machines and other regular telephone devices. 68 DSL-500T ADSL Router User's Guide Line Splitter If you are instructed to use a "line splitter", you must install the device between the Modem and the phone jack. The splitter has three RJ-11 ports used to connect to the wall jack, the Modem and if desired, a telephone or telephone device. [. . . ]