User manual D-LINK DNS-722-4

[. . . ] Table of Contents Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision 1. 0 Date November 21, 2008 Description DNS-722-4/DNS-726-4 revision A1 Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Systems, Inc. D-Link DNS-722-4/DNS-726-4 User Manual i Table of Contents Table of Contents Preface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Manual Revisions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] *DNS-722-4doesnotsupport"Recordonevent"function. D-Link DNS-722-4/DNS-726-4 User Manual 36 Section 3 - Configuration Event Setup (DNS-726-4 Only) This option may be configured and applied using DNS-726-4. Step 1: Choose the camera, and then select one of the three events. Connection lost: Action is triggered if the connection between the camera and NVR is lost. Note Before setting the event Motion from Camera, you must first configure the motion detection function on your camera Step 2: Click the Add button to setup the actions of the event. Output: If the event occurs, the system will send a signal to other connected devices. E-mail: If the event occurs, the system will send an E-mail to the pre-set contacts. Step 3: Click the action, and then click the Configure button to modify the details of that action if necessary. Step 5: Repeat step 1 through 3 to set more cameras. Note: · Inaddition, youcanalsosettheeventnotificationforwhentheharddiskisfull. · Thescreenwilldisplaytheeventinformationafteryouhaveconfiguredthesettings. D-Link DNS-722-4/DNS-726-4 User Manual 37 Section 3 - Configuration E-mail Setup This section allows you to configure the sender's email account and the contact or receiver's list. Server Address: SMTP (Simple Mail Transport Protocol) server IP address. SMTP Provide the user name and password to the Authentication: SMTP server for identification before sending E-mail. Password: Input the SMTP server login user password. Add Contacts Step 1: Insert the name of a new contact. Step 4: Click the Save Settings button to save the new contact list. D-Link DNS-722-4/DNS-726-4 User Manual 38 Section 3 - Configuration Dynamic DNS Enable this option only if you have purchased a domain name and registered with a dynamic DNS service provider. The following parameters are displayed when the option is enabled. Server Select a dynamic DNS service provider from Address: the pull-down list. Username or Enter the username or key provided by your Key: service provider. If the Dynamic DNS provider supplies only a key, enter that key in all three fields. Password or Enter the password or key provided by your Key: service provider. Verify Re-type the password or key provided by your Password or service provider. Key: Status: Displays the current status of connection to the DDNS server. D-Link DNS-722-4/DNS-726-4 User Manual 39 Section 3 - Configuration Time and Date Setup Time Zone Settings: Select your time zone from the pull-down list. Click Set Time to apply the settings. There are three choices for setting the time. NTP Server: Select or enter an NTP Server here. The NVR will contact the server you entered and receive the correct time. Click Set Time to have the NVR set its own clock according to the time on your computer. Click Set Time to apply the settings. From My Computer: Manually Set the Time and Date: D-Link DNS-722-4/DNS-726-4 User Manual 40 Section 3 - Configuration Maintenance User Management This option allows you to add users and modify or delete accounts. Step 3: Select the live view cameras and PTZ/ IO Control functions which this user can access. Step 4: Select the playback channels and Backup Data function which this user can access. Step 5: Click the Save Settings button to create a new user. Note The Administrator account can configure all functions of the NVR. [. . . ] Step 6: Click the OK button. Cannot Playback When Applying Windows 2000 1. If Media Player is installed, verify that it is version 9 or later. Cannot Login to the Unit through Internet Explorer 1. Adjust the settings of or disable anti-virus software. D-Link DNS-722-4/DNS-726-4 User Manual 78 Appendix A - Choose a RAID Level There are several issues to consider when choosing the RAID level. The following summarizes some advantages, disadvantages and applications for each choice. [. . . ]