User manual D-LINK DIR-860L DWA-182

[. . . ] Version 1. 0 | 03/22/2013 User Manual Wireless AC1200 Dual Band Gigabit Router DIR-860L Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision 1. 0 Date March 28, 2013 • Initial release Description Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation. D-Link DIR-860L User Manual i Table of Contents Preface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Manual Revisions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 6rd IPv6 Prefix: Enter the 6rd IPv6 prefix settings supplied by your ISP. Prefix: 6rd Border Relay Enter the 6rd Border Relay IPv4 address settings supplied by your ISP. IPv4 Address: Primary/ Enter the primary and secondary DNS server addresses. Secondary DNS Address: LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN Link-Local Address: Displays the Router’s LAN Link-Local Address. D-Link DIR-860L User Manual 64 Section 3 - Configuration Enable Automatic Check to enable the Automatic IPv6 Address Assignment feature. IPv6 Address Assignment: Autoconfiguration Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless Type: DHCPv6. Lifetime: D-Link DIR-860L User Manual 65 Section 3 - Configuration Link-Local Connectivity My IPv6 Select Link-Local Only from the drop-down menu. Connection Is: LAN IPv6 Address Displays the IPv6 address of the router. Settings: D-Link DIR-860L User Manual 66 Section 3 - Configuration mydlink Settings Devices that are mydlink-enabled can be accessed and managed through the mydlink website and by using mydlink mobile apps for iOS and Android. You cannot take advantage of these features without a mydlink account. If you have a mydlink account already, you can log in when you first set up the router, or by visiting this setup page. mydlink Service: Displays whether your device is registered with a mydlink account or not. mydlink E-mail: Displays the email address associated with your mydlink account if you have an active account. Register mydlink Click to go to the mydlink website to register your device or Service: edit your settings. D-Link DIR-860L User Manual 67 Section 3 - Configuration Virtual Server This page will allow you to open a single port. Name: Enter a name for the rule or select an application from the drop-down menu. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP), your computer will be listed in the “Computer Name” drop-down menu. Private Port/ Enter the port that you want to open next to Private Port Public Port: and Public Port. The public port is seen from the Internet side, and the private port is used by the application on the computer within your local network. Schedule: The schedule of time when the Virtual Server Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. Inbound Filter: Select Allow All (most common) or a created Inbound filter. [. . . ] If the address is 0. 0. 0. 0, check your adapter installation, security settings, and the settings on your router. Some firewall software programs may block a DHCP request on newly installed adapters. D-Link DIR-860L User Manual 133 Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® 7 - Windows Vista® - Windows® XP - Windows® 2000 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center. Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections. From the desktop, right-click My Network Places > Properties. Step 2 Right-click on the Local Area Connection which represents your network adapter and select Properties. [. . . ]