User manual D-LINK DGS-3224TGR Reference Guide

[. . . ] DGS-3224TGR Layer 2 Switch Command Line Interface Reference Manual First Edition (October 2003) 6S24TGRCLI01 Printed In China RECYCLABLE i Trademarks Copyright 2003 D-Link Corporation. D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to their respective proprietors. Copyright Statement No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems Inc. , as stipulated by the United States Copyright Act of 1976. ii Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Using the Console CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Command Syntax. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Basic Switch Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] None. 118 DGS-3224TGR Layer 2 Gigabit Ethernet Switch User's Guide disable hol_prevention Restrictions You must have administrator privileges. Example Usage: To disable HOL prevention: DGS-3224TGR:4# disable hol_prevention Command: disable hol_prevention Success. DGS-3224TGR:4# show hol_prevention Purpose Syntax Description Parameters Restrictions Used to show HOL prevention. show hol_prevention The show hol_prevention command displays the Head of Line prevention state. None. Example Usage: To show HOL prevention: DGS-3224TGR:4# show hol_prevention 119 DGS-3224TGR Layer 2 Gigabit Ethernet Switch User's Guide Command: show hol_prevention Success. DGS-3224TGR:4# 120 DGS-3224TGR Layer 2 Gigabit Ethernet Switch User's Guide 14 PORT MIRRORING COMMANDS The port mirroring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command config mirror port enable mirror disable mirror show mirror Parameters <port> [add|delete] source ports <portlist> [rx|tx|both] Each command is listed, in detail, in the following sections. config mirror port Purpose Syntax Used to conigure a mirror port - source port pair on the switch. config mirror port <port> add source ports <portlist> [rx|tx|both] 121 DGS-3224TGR Layer 2 Gigabit Ethernet Switch User's Guide config mirror port Description This command allows a range of ports to have all of their traffic also sent to a desnigated port - where a network sniffer or other device can monitor the network traffic. In addition, you can specify that only traffic received by or sent by or both is mirrored to the Target port. <port> - This specifies the Target port (the port where mirrored packets will be sent). <portlist> - This specifies a range of ports that will be mirrored. That is, a range of ports for which all traffic will be copied and sent to the Target port. The port list is specified by listing the beginning port number on that switch and the highest port number of the range. 3-4 specifies all of the ports between port 3 and port 4 - in numerical order. rx - Allows the mirroring of only packets received (flowing into) the port or ports in the port list. tx - Allows the mirroring of only packets sent (flowing out of) the port or ports in the port list. both - Mirrors all the packets received or sent by the port or ports in the port list. Parameters 122 DGS-3224TGR Layer 2 Gigabit Ethernet Switch User's Guide config mirror port Restrictions Only administrator-level users can issue this command. Example Usage: To add the mirroring ports: DGS-3224TGR:4#config mirror port 10 add source ports 1-5 both Command: config mirror port 10 add source ports 1-5 both Success. DGS-3224TGR:4# config mirror delete Purpose Syntax Description Used to delete configuration| a port mirroring config mirror <port> delete source <portlist> [rx|tx|both] This command is used to previously entered port configuration. delete a mirroring Parameters <port> - This specifies the Target port (the port where mirrored packets will be sent). <portlist> - This specifies a range of ports that will be mirrored. That is, a range of ports for which all traffic will be copied and 123 DGS-3224TGR Layer 2 Gigabit Ethernet Switch User's Guide config mirror delete sent to the Target port. rx - Allows the mirroring of only packets received (flowing into) the port or ports in the port list. tx - Allows the mirroring of only packets sent (flowing out of) the port or ports in the port list. both - Mirrors all the packets received or sent by the port or ports in the port list. [. . . ] Restrictions None. Usage Example: To configure the SSH server: DGS-3224TGR:4#config ssh server maxsession 8 contimeout 300 authfail 2 Command: config ssh server maxsession 8 contimeout 300 authfail 2 Success. DGS-3224TGR:4# show ssh server 220 DGS-3224TGR Layer 2 Gigabit Ethernet Switch User's Guide show ssh server Purpose Syntax Description Parameters Restrictions Used to display the SSH server setting. show ssh server This command allows you to display the current SSH server setting. None. Usage Example: To display the SSH server: DGS-3224TGR:4#show ssh server Command: show ssh server The SSH server configuration Max Session :8 Connection Timeout : 300 Authfail Attempts :2 Rekey Timeout : 60min DGS-3224TGR:4# enable ssh Purpose Syntax Description Used to enable SSH. [. . . ]