User manual D-LINK DES-1316

[. . . ] D-Link DES-1316 Web-Smart 8-Port 10/100Mbps Ethernet Switch with 8 10/100Mbps 802. 3af Power Over Ethernet Ports Manual First edition Building Networks for People FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CE Mark Warning This is a Class A product. [. . . ] This function helps you to refresh the time for monitoring the device. Choose 15 secs, 30 secs, 1 min, 2 min, and 5 min to select the time for monitoring. In the "Help TAB", there is About function, it will show out the version of the Web Management Utility. Configuring the Switch The 16-Port 10/100Mbps Ethernet Web Smart Switch with 8-Port PoE has a Web GUI interface for smart switch configuration. A network administrator can manage, control, and monitor the Switch from the local LAN. 26 This section indicates how to configure the Switch to enable its smart functions including: Port Setting (Speed/Disable, and Flow Control) VLAN Setting (802. 1Q VLAN) Trunking Port Mirroring PoE Setting System Setting Device status and Statistic Login Before you configure this device, note that when the Web Smart Switch is configured through an Ethernet connection, make sure the manager PC is set on same the IP network. For example, when the default network address of the default IP address of the Web Smart Switch is 192. 168. 0. 1, then the manager PC should be set at 192. 168. 0. x (where x is a number between 2 and 254), and the default subnet mask is 255. 255. 255. 0. Enter the IP address http://192. 168. 0. 1 (the factory-default IP address setting) into the address location. Figure 12. 27 Or through the Web Management Utility, you do not need to remember the IP Address. Select the device shown in the Monitor List of the Web Management Utility to settle the device on the Web Browser. When the following dialog page appears, enter the default password "admin" and press Login to enter the main configuration window. Figure 13. After entering the password, the main page appears, and the screen will display the device status. 28 Figure 14. Device Status 29 Setup Menu When the main page appears, find the Setup menu on the left side of the screen (Figure 15). There are eleven options: Port Settings, VLAN Settings, Trunk Settings, Mirror Settings, PoE Settings, Device Status, Statistic, System Settings, Trap Setting, Password Settings, Backup Settings, and Reset Settings as shown in the Main Menu screen. Figure 15. Setup menu 30 Configuring Setup Setting There are six items, including Port Settings, VLAN Settings, Trunk Settings, Mirror Settings, and PoE Settings in Setup menu. Port Settings In the Port Settings menu (Figure 16), this page will display each port's status. Press the ID parameter to set each port's Speed, Flow Control, Rate Control Ingress, and Egress. When you need to renew the posted information, press the "Refresh" button. The Link Status in the screen will display the connection speed and duplex mode; otherwise this dialog box will display down when the port is disconnected. Figure 16. Port Configuration 31 To change the port setting, click on the ID parameter to enter the selected port to configure its Speed/Disable and Flow control. Figure 17. Speed/Disable: This setting has six modes--100M Full, 100M Half, 10M Full, 10M Half, Auto, and Disable--for speed or port disable selections. Flow Control: This setting determines whether or not the Switch will be handling flow control. If it is set to Disable, there is either no flow control or other hardware/software management. 32 When the 10/100M port is set to full-duplex mode, then the flow control will be automatically set to disable; and if the 10/100M port is set to half-duplex mode, the flow control will be automatically set to enable. QoS: In some ports that need to have a high priority to manage the data transfer, QoS should be change, Set the port's QoS to high to determine the port will always transfer their data first. VLAN Settings (Virtual Local Area Network) A VLAN is a collection of switch ports that make up a single broadcast domain. [. . . ] D-Link will only replace the defective portion of the Product and will not ship back any accessories. The customer is responsible for all in-bound shipping charges to D-Link. Products sent COD will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc. , 17595 Mt. [. . . ]