User manual D-LINK DCS-2120 GUIDE D INSTALLATION RAPIDE

[. . . ] Table of Contents Table of Contents Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] That is, if you make changes in one time-line, the corresponding changes will be applied with scale to the other three time-lines in the same schedule. Before you begin, make sure that you select "Once" (page 83) if you want to choose the days to record on. It includes the time-line, schedule information, and the selected day in the week. Marking/Unmarking the Recording Time on the Week Time-Line The corresponding changes for the markers on the week time-line will be automatically added to the hour time-lines, which is shown above. You can also mark and unmark the plotted bar by clicking and dragging with the left and the right mouse button. Hour Time-Line In the figure below, the Hour time-line is displayed. D-Link DCS-10 User Manual Section - Configuration Marking/Unmarking the Recording Time on the Hour Time-Line You can apply the one-click function by clicking the left mouse button and dragging to mark the time on this time-line. The operating method for the hour time-line is the same as that of the week time-lines. Please refer to the previous section about marking/unmarking on the week time-line for more details. Schedule with Time Picker Begin and End Time There are three controlling units in both "Begin Time" and "End Time" selectors shown below. You can select day with it to set the beginning time and the ending time for the recording interval. You can change the hour and minute settings for the beginning and ending time with them. Note: The time set in "Begin time" must be earlier than that in "End time". Apply and Erase Buttons After you have selected the time period with "Begin time" and "End time" picker, you can apply the period picker, shown in the figure below, to set the periodical types of the time interval set previously. After the settings in "Begin Time", "End Time" and "Period Picker" are all done, you should click the "Apply" button or "Erase" button on the right to add or clear this scheduling information to the editing schedule scheme. Note that only after you click on the "Apply" button, the scheduling information settings will be written back into the whole editing schedule scheme. That means this edited scheduling time interval is valid only after you "Apply" the changes. D-Link DCS-10 User Manual Section - Configuration Schedule in Event Mode You can select to record in Event mode or Continuous mode by the Schedule mode selector as shown in the figure below. Please refer to the following two sections for more information. Motion Detection As shown below, you can check the windows that you would like to record while the motion detection is triggered. Digital Input In the figure below, there are four conditions for the digital input. Check the condition that you would like to record while the condition triggers. Note: The Digital Input is not available for the DCS-2120 camera. D-Link DCS-10 User Manual Section - Configuration High: Checking this will trigger recording while the digital input is high. Low: Checking this will trigger recording while the digital input is low. Rising: Checking this will trigger recording while the digital input is changing from low to high. Falling: Checking this will trigger recording while the digital input is changing from high to low. The technical name for this event is edge trigger. Schedule in Continuous mode If you select Continuous mode in the schedule mode selector, it will record continuously during the schedule that is set up by the user. Secondary Schedule Secondary schedule is for recording outside of the primary schedule. The secondary schedule provides options to record without a specified date or time. Schedule modes There are three modes in the secondary schedule: Disable, Event mode, and Continuous mode. If event mode is selected in the secondary schedule, the camera will record whenever an event is triggered. [. . . ] D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in the United States, otherwise we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are prepaid by the customer. [. . . ]