User manual D-LINK DAP-3410

[. . . ] Version 3. 0 | 21/05/2014 User Manual Wireless N Exterior Access Point DAP-3410 Table of Contents Table of Contents Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Public WAN IP If the Multiple DMZ option is selected, this Address: field will be available. This should be set to the external IP address that will be assigned to an internal IP address of a computer or device. Local DMZ IP If the Multiple DMZ option is selected, this Address: field will be available. This should be set to the internal IP address of a computer or device that will be assigned to an external IP address. D-Link DAP-3410 User Manual 41 Section 3 - Configuration Virtual Server This will allow you to open a single port. This allows a computer or device to provide external access to services or applications that are otherwise blocked by the built-in firewall. To create a virtual server, click on Create New Virtual Server, and the following settings will appear: Service: Select to either Disable or Enable the rule. Private IP: Enter the IP address of the computer on your local network that you want to allow the incoming service to. Private Port: Enter the port that you want to open for the computer or device on the internal network. Public Port: Enter the port that you want to open for the external network. The public port is the port seen from the Internet side, and the private port is the port being used by the application on the computer or device within your local network. D-Link DAP-3410 User Manual 42 Section 3 - Configuration Parental Control Parental Control is used to allow you to set up a range of IP Addresses that can be either be blacklisted or whitelisted to certain MAC addresses on the network. Active: Select to either Disable or Enable the Parental Control feature. MAC Address: Enter the MAC address to be monitored and click Save to add it to the parental control list. Local IP: Enter the start and end of an IP address range that you would like to filter on the local network. This is normally used to prevent access to certain parts of the internal network. Destination IP: Enter the start and end of an IP address range that you would like to filter on the destination network. This is normally used to prevent access to certain parts of the external network. Destination Enter the specific port to filter on the destination Port: network. D-Link DAP-3410 User Manual 43 Section 3 - Configuration Static Routing Setup This page will allow you to configure the built-in routing protocols that the DAP-3410 allows when in certain operating modes. OSPF Service Select to either Disable or Enable the AP from offering OSPF service. This should be the main interface that will connect to the local network. Network Selecting this checkbox will allow you to enter (Internal): an area that will be used by the static routing setup on the internal network. Network Selecting this checkbox will allow you to enter (External): an area that will be used by the static routing setup on the external network Distribute RIP Enabling this option will allow the router to over OSPF: broadcast the RIP routing protocol over OSPF. RIP Service: Select to either Disable or Enable the AP from offering RIP routing services. Side (Devices): Select the checkbox for the interface that will allow clients to connect to. [. . . ] Secure your wireless network by turning on the WPA or WEP security feature on the access point. Refer to product manual for detail information on how to set it up. Wireless Modes There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless bridge. • Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more wireless network Cardbus adapters. An Infrastructure network contains an Access Point or wireless bridge. [. . . ]