User manual D-LINK AIRPLUS XTREME G DWL-2100AP

[. . . ] D-Link AirPlus Xtreme G DWL-2100AP 802. 11g Wireless 108Mbps Access Point ® Manual V2. 10 Building Networks for People Contents Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The open button is used to load a previously saved configuration file. After opening a configuration file, you must click the Apply button to save the settings to the selected device(s). The save button allows you to save a configuration file of the selected device settings. You cannot save a configuration file if you selected more than one device in the device list. Any settings that haven't been applied will be lost. 45 Using the AP Manager (continued) Device Configuration>General When selecting multiple devices for configuration, some options are unavailable for configuration as noted(*) below: · Device Name(*): This allows you to change the device name for the selected access point. This option can only be configured when one access point is selected for configuration. · IP address and Subnet Mask(*): If you've selected one device for configuration and you want to change the IP address of the device, check the IP Address box. You can then enter an IP address and Subnet Mask for the selected access point. This option is only configurable when one access point is selected for configuration. To configure multiple devices with an IP address at one time, please reference the previous page. · Gateway: Enter the IP address of your gateway, typically your router address. · DHCP client: There is a pulldown menu to select enabled or disabled. When enabled, the selected device(s) will function as a DHCP client(s). This allows them to receive IP configuration information from a DHCP server. When disabled, the access point(s) must have a static IP address assigned to them. 46 Using the AP Manager (continued) Device Configuration>General (continued) · Telnet Support: This pulldown selection enables or disables the ability to Telnet into the selected device(s). · Telnet Timeout: This pulldown selection defines the timeout period during a Telnet session with the selected device(s). 47 Using the AP Manager (continued) Device Configuration>Wireless · SSID: The Service Set (network) Identifier of your wireless network. · SSID Broadcast: Allows you to enable or disable the broadcasting of the SSID to network clients. · Super G: Super G is a group of performance enhancement features that increase end user application throughput in an 802. 11g network. For ideal performance, all wireless devices on the network should be Super G capable. The modes are listed below: · Radio Wave: Enable or disable the wireless functionality of the selected device(s). · Data Rate: A pulldown menu to select the maximum wireless signal rate for the selected devices(s). · Beacon Interval (20~1000): Beacons are packets sent by an access point to synchronize a network. [. . . ] D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link, with shipping charges prepaid. Expedited shipping is available if shipping charges are prepaid by the customer and upon request. Herrmann, Fountain Valley, CA 92708 Canada: 2180 Winston Park Drive, Oakville, ON, L6H 5W1 (Visit http://www. dlink. ca for detailed warranty information within Canada) · · · D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. [. . . ]