User manual D-LINK AIRPLUS DWL-650+

[. . . ] D-Link AirPlus DWL-650+ ® 2. 4 GHz Wireless Cardbus Adapter Manual Rev. 3 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 2 1. Package Contents Contents of Package: · · · D-Link AirPlus DWL-650+ 2. 4GHz Wireless Cardbus Adapter Manual, QIG, and Drivers on CD Printed Quick Installation Guide If any of the above items are missing, please contact your reseller. System Requirements: · · · · · A laptop computer with an available 32-bit Cardbus PC Card slot Windows XP, Windows 2000, Windows Me, or Windows 98 Cardbus Controller, properly installed and working At least 32 MB of memory and a 300 MHz processor An 802. 11b Access Point (e. g. , DWL-1000AP for Infrastructure Mode) or another 802. 11b wireless adapter (e. g. , DWL-520 for AdHoc mode. ) 3 2. Introduction The D-Link AirPlus DWL-650+ Wireless Cardbus Adapter is an enhanced 802. 11b high-performance, wireless adapter that supports high-speed wireless networking at home, at work or in public places. [. . . ] This prevents several clients from trying to establish a BSS at the same time, which can result in multiple singular BSSs being established, rather than a single BSS with multiple clients associated to it. Check that the Network Connection for the wireless client is configured properly. Select AP (Infrastructure) when connecting to an access point and select Ad-Hoc mode when connecting without an access point. Double-click on the WLAN icon in the taskbar > click on Configuration to change the settings for the wireless adapter. · · · · · If Security is enabled, make sure that the correct encryption keys are entered on both the DWL-650+ and the access point. Check to see that the key selected is set to the same key as other devices on the network. 25 8. Networking Basics Using the Network Setup Wizard in Windows XP In this section you will learn how to establish a network at home or work, using Microsoft Windows XP. Note: Please refer to websites such as http://www. homenethelp. com and http://www. microsoft. com/windows2000 for information about networking computers using Windows 2000, ME or 98. Go to Start > Control Panel > Network Connections Select Set up a home or small office network Fig. 8. 1 When this screen appears, click Next. 26 Networking Basics Using the Network Setup Wizard in Windows XP Please follow all the instructions in this window: Fig. 8. 2 Click Next In the following window, select the best description of your computer. If your computer connects to the Internet through a gateway/router, select the second option as shown. Fig. 8. 3 Click Next 27 Networking Basics Enter a Computer description and a Computer name. Fig. All computers on your network should have the same Workgroup name. Fig. 8. 5 Click Next 28 Networking Basics Please wait while the wizard applies the changes. Fig. 8. 7 29 Networking Basics In the window below, select the best option. 8. 8 Insert a disk into the Floppy Disk Drive, in this case drive A: Fig. 8. 9 Format the disk if you wish, and click Next. 30 Networking Basics Please wait while the wizard copies the files. Fig. 8. 10 Please read the information under Here's how in the screen below. After you complete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on your network. 8. 11 31 Networking Basics Please read the information on this screen, then click Finish to complete the Network Setup Wizard. Fig. 8. 12 The new settings will take effect when you restart the computer. Next, you will need to run the Network Setup Disk on all the other computers on your network. After running the Network Setup Disk on all your computers, your new wireless network will be ready to use. 32 Networking Basics Naming your Computer To name your computer, please follow these directions: In Windows XP: · Click Start (in the lower left corner of the screen) · Right-click on My Computer · Select Properties and click Fig. [. . . ] · The customer is responsible for all shipping charges to and from D-Link (No CODs allowed). Products should be fully insured by the customer and shipped to D-Link Systems Inc. , 53 Discovery Drive, Irvine CA 92618. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The 61 product owner agrees to pay D-Link's reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming. [. . . ]