User manual CULLIGAN MEDALLIST PLUS SERIE 45

[. . . ] Culligan Medallist Series® Automatic Water Conditioner Owners Guide Thank You And Welcome To Your New World Of Better Living With Culligan Water. The Culligan Medallist Plus Series® 30, 45 and 60 Water Softeners are tested and certified by WQA against NSF/ANSI Standard 44 for the effective reduction of hardness (calcium and magnesium) as verified and substantiated by test data. For installations in Massachusetts, Massachusetts Plumbing Code 248 CMR shall be adhered to. This system and its installation must comply with state and local regulations. Hardness sample kits are available through your local Culligan Dealer. If this is your first experience having soft, conditioned water in your home, you'll be amazed at the marvelous difference it makes. [. . . ] The display will blink "dIP7" for 3 seconds and then show the current status. Toggle between "3-4" and "InCH" with the "+" or "-" key. Note: The 3/4" meter setting is to be used with the 8" Medallist Series softener. The 1" meter setting is for the Medallist Plus series softener. 6. 7. 3-4 18 Setting the Microprocessor The microprocessor senses when it is installed as a Soft-Minder® control. Adding or removing any connection to the board will automatically reset the microprocessor to the factory settings. Step 1 ­ Programming Time of Day Press the "STATUS" key. The display will blink "tod" for 3 seconds and then change to time of day with the "minutes" digits blinking. Adjust the "minutes" digits with the "+" or "-" keys. Press the "REGEN" key to blink the "hours" digits. Adjust the "hours" digits with the "+" or "-" keys. PM Press the "REGEN" key to cycle back to "minutes" Note: The "hours" setting scrolls through 1-12 and 1-12 PM. Make sure the proper AM or PM indicator is shown when setting the time (AM is not displayed). Programming (cont. ) 12:00 2:00 10 10 Step 2 ­ Programming Regeneration Time Press the "Status" key after setting the time of day. The display will blink "tor" for 3 seconds and then change to the time setting with the "ones" digit blinking. Note: This option will not show if the "dIP 2" option is set to immediate Step 3 ­ Programming Salt Dosage Press the "Status" key after programming regeneration time. The display will blink "SLtP" if set to English or "SLtG" if set to Metric for 3 seconds and then display the salt dosage. Adjust the setting with the "+" or "-" key (3-24 lbs. ) (1-10 kgs. ) Note: This option will not show if the control is set to Filter mode. Step 4 ­ Programming Backwash Time Press the "Status" key after programming salt dosage. The display will blink "bw" for 3 seconds and then display the backwash time in minutes. (1-40 minutes) 19 Programming (cont. ) Step 5 ­ Programming Brine Draw/Slow Rinse Time Press the "Status" key after programming the backwash time. The display will blink "br" for 3 seconds and then display the brine draw/slow rinse time in minutes. Step 6 ­ Programming Gallons (Liters) or Days to Regeneration Meter Mode Press the "Status" key after programming the brine draw/slow rinse time. The display will blink "CAPG" ("CAPL") for 3 seconds and then display the gallons or liters set point. [. . . ] As an expression of our confidence in Culligan International Company products, your water conditioner is warranted to the original end-user, when installed in accordance with Culligan specifications, against defects in material and workmanship from the date of original installation, as follows: For a period of ONE YEAR For a period of FIVE YEARS For a period of TEN YEARS The entire conditioner The AccuSoft® circuit board, or Soft-Minder® meter, if so equipped The control valve body, excluding internal parts The conditioner tank The salt storage container, brine valve and all its component parts The Cullex® resin Culligan Limited Warranty For the LIFETIME of the original consumer purchaser If a part described above is found defective within the specified period, you should notify your independently operated Culligan dealer and arrange a time during normal business hours for the dealer to inspect the water conditioner on your premises. Any part found defective within the terms of this warranty will be repaired or replaced by the dealer. We are not responsible for damage caused by accident, fire, flood, freezing, Act of God, misuse, misapplication, neglect, oxidizing agents (such as chlorine, ozone, chloramines and other related components), alteration, installation or operation contrary to our printed instructions, or by the use of accessories or components which do not meet Culligan specifications, is not covered by this warranty. Refer to the specifications section in the Installation and Operating manual for application parameters. [. . . ]