User manual CUISINART DGB-475BK

[. . . ] Grind & Brew Automatic Coffeemaker TM DGB-475 For your safety and continued enjoyment of this product, always read the instruction book carefully before using. ImportAnt SAfeGuArDS When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock and/or injury to persons, including the following: 1. To protect against electric shock, do not place cord, plug, or base unit in water or other liquids. This appliance should not be used by or near children or individuals with certain disabilities. Allow to cool before putting on or taking off parts and before cleaning the appliance. [. . . ] Setting the Program Time When you press the Program Set button, it displays the current program time (default time 12:00 p. m. ). Entering Set Program Time Mode Press and hold the Program button (about 2 seconds) until the green light and LCD display begin to flash. The desired time can be set by pressing the Hours and Min buttons to scroll forward through the digits. Pressing and holding either button will allow you to scroll continuously, slowly at first, and then to accelerate to the rate of about three digits per second. As the desired time setting approaches, release the button and then press repeatedly to advance one digit at a time. The Automatic Shutoff Time can be programmed anywhere from immediate shutoff after completion of the brew cycle up to four hours. The 0:00 setting shuts the unit off immediately after brewing is complete. To check the current setting, press and hold the On/Off button and the Automatic Shutoff Time will be displayed. To change the preset time, press and hold the On/Off button until the red power light and LCD display begin to flash. Press the Hours and Min buttons to scroll forward through the digits until desired time appears. When it's at 4:00, the next press key of Hour will roll back to 0:00, since four hours is the maximum Automatic Shutoff setting. Pressing and holding either button will allow you to scroll continuously, slowly at first, and then to accelerate to the rate of about three digits per second. As the desired time setting approaches, release the button and then press repeatedly to advance one digit at a time. The Automatic Shutoff Time (ASO) may be 8 programmed either before or during coffee brewing. If you do so, the Grind & BrewTM will automatically account for any time that has already elapsed after brewing. For example, if you set the ASO for 40 minutes and 25 minutes have already elapsed, the Grind & BrewTM will shut off automatically after 15 minutes (40 minutes minus the 25 elapsed equals 15 minutes). Turning off Grind Function note: Caution must be used when inserting the charcoal filter. Improper placement in the holder can cause tearing of the filter skin. You should place the hole openings in the side of the unit directly under the water stream. Replace the water filter holder in the reservoir area of the coffeemaker, pushing it all the way down to the base of the unit, along the reservoir wall. note: We recommend changing the water filter every 60 days or 60 uses, more often if you have hard water. Replacement water filters can be purchased in stores or by calling customer service or through the Cuisinart web site. To turn off the grinding function, press the Grind Off button. Remove the filter from polybag and soak in cold tap water for 15 minutes. Remove the water filter holder from the coffeemaker by lifting it out of the reservoir area with your thumb and forefinger. Compartment will flip open. mAKInG Coffee Before you make the first pot of coffee in your new Cuisinart® Grind & BrewTMAutomatic coffeemaker, we recommend operating the coffeemaker once, using only water and a paper filter. [. . . ] Except as otherwise required under applicable law, this warranty is not available to retailers or other commercial purchasers or owners. We warrant that your Cuisinart® Grind & BrewTM Automatic Coffeemaker will be free of defects in materials and workmanship under normal home use for 3 years from the date of original purchase. We suggest you complete and return the enclosed product registration card promptly to facilitate verification of the date of original purchase. However, return of the product registration card does not eliminate the need for the consumer to maintain the original proof of purchase in order to obtain the warranty benefits. [. . . ]