User manual CRISP SOLUTIONS UC-525

[. . . ] Universal LCD Remote Control With Touchscreen & Learning Function User's Guide The UC-525 User's Guide Preface About this User's Guide This user's guide is designed to assist you in setting up your UCommand-525 Universal LCD Remote Control. Information in this document has been carefully checked for accuracy; however, no guarantee is given as to the correctness of the contents. The information contained in this document is subject to change without notice. Edition First Edition, May 2001 Copyright ©2001 Crisp Solutions LLC, all rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the prior written permission of the publisher. Trademarks Trademarks and registered trademarks of products referred to in this user's guide are the properties of their respective holders. Radio Frequency Interference This device complies with Part 15 of the FCC Rules. [. . . ] You can delete the button, or choose one of the available icon layouts. Note: If you don't find the right icon to represent your device function, you may use an empty button (figure C. ) to represent the function. You hear three beeps and the UC-525 goes back to normal mode. 20 -- Operating the UC-525 Changing the AUX Device Layout The AUX Device screen layout can be made identical to any of the other device buttons. · Enter the "LCD layout edit mode" for the AUX Device button by pressing the AUX button for three seconds (this function is activated the same way as described in the previous chapter "Changing the LCD Layout"). When the screen flashes, press the device button of the device you want to copy. You will hear three beeps and UC-525 will return to normal operating mode. · · Macro Function The macro feature enables you to store up to 25 commands on any command button. When you have created a macro, you will be able to run a chain of commands by pushing only one button. You can assign macros to any regular button but not to device buttons. When you assign a macro to a command button, the original function of the button will be lost. Therefore you should choose a button that you do not use in normal operation. Using a device button will remove the button's function from the layout. For example, if you use the TV device button for the macro run key, you will not be able to use the UC-525 to control your TV set. 21 The UC-525 User's Guide Macro setup Follow these instructions to set up a macro: Press the MACRO button for three seconds. You hear a beep and then you see the unlock screen to the right. Note: This screen prevents you from accidentally modifying your UC-525. Press each number button in any order until it disappears. 22 -- Operating the UC-525 The LEARN icon appears under the LEARN button. First, press the button that you want to become the macro button. For details, refer to the next section: Macro example Press the LEARN button to end the macro recording for this macro. If you want to record another macro, press a different macro run key and record the macro. To exit, press the LEARN button. Time Delays between macro commands A chain of macro commands is usually played back quite quickly. Time delays are useful if your device needs time between two IR commands. For example, after powering up your TV, it might take a few seconds before it can recognize an Input command. For setting time delays, refer to the next section, "Macro example". 23 The UC-525 User's Guide Macro example The following example will help you to better understand recording a macro. This example macro would be used to turn on your TV, switch to VCR input, and start playing a tape: Press the MACRO button for three seconds to enter macro setup mode. Press each number button until it disappears. Press the AUX button to open the AUX screen. The 1 button in the AUX screen will be used to start the macro during normal operation mode. Using a device button will remove the button's function from the layout. For example, if you use the TV device button for the macro run key, you will not be able to use the UC-525 to control your TV set. A. [. . . ] See Appendix E · · Problems learning from 2-way remotes · Problems learning repetitive commands, such as Volume Control · · Problems learning sound field commands from SONY Amplifiers · 35 The UC-525 User's Guide The LCD screen turns off. · The UC-525 is preset at the factory to automatically switch the LCD off after 20 minutes if left unused. Just tap the LCD screen to turn the UC-525 back on again. 36 -- Appendix BC Appendix C Frequently Asked Questions Can I control X10 devices?· · See Appendix D Holding the Power button while in Edit Mode will display all icons. · Yes, you can map multiple devices to the same device layer. [. . . ]