User manual CRESTRON WPR-48

[. . . ] Crestron WPR-48 Waterproof Wireless Handheld Remote Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON WARNING: The WPR-48 Waterproof Wireless Handheld Remote has been tested and found to be waterproof when submerged to a maximum depth of 1 meter, and for a maximum duration of 30 minutes, per IEC 60529 IPX7 standards. Exceeding these limits may result in damage to the equipment, possible personal injury, and void the product warranty. That is, the eight screws that secure the rear cover to the button faceplate are not fully tightened, to simplify the process of installing button labels, as described in this Operations Guide. [. . . ] The "Enter Text Area Label" window appears as shown in the following illustration. 3. The label is tapered at the top and bottom. You can enter from one to six alphanumeric characters in the narrowest fields, and from one to seven, eight, or nine characters in wider fields. You can select any of the three fonts available from the drop-down list-- Arial, Crestron Transport, or Crestron Transport Outline--but you cannot mix fonts in a single field. You can, however, use the Field One and Field Two entry fields, which together form one line of text, to combine two different fonts, for example VOLK and VOLJ. The Crestron Transport font consists of symbols that represent standard device functions such as Fast Forward, Rewind, Up and Down. Each symbol corresponds to a letter of the alphabet (from A to P, not casesensitive) as follows: a A i I b B j J c C k K d D l L e E m M f F n N g G o O h H p P Operations Guide ­ DOC. 6254A Waterproof Wireless Handheld Remote: WPR-48 · 11 Waterproof Wireless Handheld Remote 4. Crestron WPR-48 Once you have entered all the desired button legends, save the file and print the file. Cut out the labels, cutting just inside the lines that define the label area. To install the labels, refer to the "Installing/Replacing Button Labels" procedure, which follows. 5. Installing/Replacing Button Labels To install or replace button labels in the WPR-48, the unit must be disassembled and, after placing the labels in position, carefully reassembled. Using a #1 Phillips screwdriver, remove the eight cover screws securing the rear cover to the button faceplate, and lift the rear cover from the assembly. (Refer to the following illustration. ) CAUTION: Avoid contact with the electronic circuitry attached to the rear cover, to prevent damage to the equipment. WPR-48 Assembly View 2. During disassembly, the gasket may become separated from the rear cover and the button faceplate. If this occurs, carefully assemble the gasket to the button faceplate with the deeper side down as shown in the preceding graphic. CAUTION: The reassembly procedure must be done carefully to ensure that the WPR-48 will be waterproof. 12 · Waterproof Wireless Handheld Remote: WPR-48 Operations Guide ­ DOC. 6254A Crestron WPR-48 3. Waterproof Wireless Handheld Remote Place the button labels in position, face down, and carefully assemble the rear cover to the button faceplate, making certain the gasket is properly seated. Use two or three screws to hold the assembly together and turn the unit over to verify that the button labels are properly positioned and can be easily seen. Then add the remaining screws and tighten all eight screws evenly just until the gasket is no longer visible between the button faceplate and the rear cover (from 1. 5 to 2 in/lbs, maximum). To do so may damage the gasket such that the unit is no longer waterproof. Exposing such a unit to water may result in damage to the equipment, possible personal injury, and void the product warranty. Installing Alternate Foot To install the alternate blank foot (supplied), refer to the following illustration and perform the associated procedures. 1. Using a #1 Phillips screwdriver, remove the two pan head Phillips screws securing the lanyard foot to the rear cover of the WPR-48, and carefully remove the foot. Retain the lanyard foot (note the placement of the lanyard end knots in the cavity of the lanyard foot) for use at another time. Assemble the blank foot to the rear cover as shown, and secure with the screws removed in Step 1. 2. 3. WARNING: The lanyard, supplied with the lanyard foot, poses a possible strangulation hazard. Crestron does not recommend placing the lanyard around the neck as a means of carrying the WPR-48. Do not leave the lanyard, or the WPR-48 with lanyard foot and lanyard attached, unattended in any area where children or pets may be present. [. . . ] To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ]