User manual CRESTRON UG STS STS-C

[. . . ] Crestron ST-1550 & ST-1550C SmarTouch STS Touchpanels Contents SmarTouch STS SmarTouch STS Description Functional Description Physical Description General Use and Safety Recommended Touchpanel Cleaning Applying Power Configuring the Touchpanel Calibration Preferences Menu Power Management Advanced Settings Internal Scheduler Button Sequence Development Scheduling a Sequence/Button Press Touchpanel as Part of SmarTouch STS Introduction SmarTouch STS Hookup Problem Solving Troubleshooting Further Inquiries 1 1 1 2 2 3 3 3 4 5 7 8 9 9 10 11 11 11 13 13 13 User's Operations Guide - DOC. 5804 Contents · i Crestron ST-1550 & ST-1550C SmarTouch STS Touchpanels SmarTouch STS SmarTouch STS Description Functional Description The SmarTouch STS touchpanels are Crestron's six inch touchscreen control panels that can be used in either a Cresnet remote control system or as part of the SmarTouch STS. These touchpanels provide a means of user interface via one-way RF communication. Three offer 256 color display and are denoted with the suffix "-C". [. . . ] These buttons have special software identities (reserve join numbers) and can be recreated and programmed onto any page in the project. To reactivate the touchpanel after the Off or Standby buttons have been utilized, simply press the touchscreen. Down and up arrow buttons decrease and increase the timeout, respectively. However, Power Down Timeout should be set greater than Standby Timeout. NOTE: If the external AC power pack is attached to the touchpanel and plugged into an active AC receptacle or if the touchpanel is resting in the docking station (ST-DS) and plugged into an active AC receptacle, the panel does not power down when the power down timeout is achieved. Recall that the purpose of the this timeout is to maximize battery life. After timeout parameters have been set, touch the SAVE TIMEOUTS button in the lower left corner of the ST-1550C to save the new settings. Touch the RETURN button, located in the bottom right corner of the screen, to display the Preferences and Settings Menu. For the ST-1550, simply touch the SAVE TIMEOUTS and RETURN button. Advanced Settings The Advanced Settings button from the Preferences and Settings Menu should only be used under supervision from the dealer that provided your system. The options available from the Advanced Settings Screen, shown on the next page, are beyond the scope of this guide. 8 · SmarTouch STS User's Operations Guide - DOC. 5804 Crestron ST-1550 & ST-1550C Advanced Settings Screen SmarTouch STS Touchpanels Internal Scheduler Crestron offers an internal scheduler feature built into the touchpanel. There are actually two parts to the internal scheduler: developing a button sequence and scheduling a button sequence/function. Sequences and schedules can be programmed into your system by the dealer that supplied your system. However, with proper and careful project design by the programmer, you can easily make adjustments to the system to better suit your personal needs and way of life. Furthermore, you can schedule an event so that it can begin at any given date and time and reoccur as you see fit. An event is defined as the actions initiated by one sequence or a single button function. NOTE: Since the exact screen layout for your system is unique, the following descriptions for the two parts of the internal scheduler is only a generalization. If you decide to take advantage of this feature, consult your dealer for the personal layout details of your system. Button Sequence Development A button sequence differs from macros created from the Control pull-down menu of the programming software, because the end user can assign actions to the sequence. The purpose of developing a button sequence is to build a consecutive order of preselected buttons that runs in real time when a single programmed button is touched. The buttons in the sequence can be chosen from any page in the project. There are two buttons that must be touched when developing a sequence. One button initiates the "learning" function and the other terminates it. [. . . ] Refer to the latest revision of the STIRP Installation Instructions (Doc. Furthermore, your SmarTouch dealer should provide a listing of equipment that needs to be connected via the STIRP to each IR OUT port. For example, in the connection diagram provided, the STIRP in IR PORT A is attached to the VCR. Consult the appropriate document listed in "Applying Power" on page 3. [. . . ]