User manual CRESTRON UG CLS-C6 CLS-C6M CLSI-C6 CLSI-C6M

[. . . ] The CLS-C6 and CLS-C6M are designed for 120 VAC 50/60 Hz installations; the CLSI-C6 and CLSI-C6M are designed for 230 VAC 50/60 Hz installations. The units are functionally identical, except that the CLS/CLSI-C6M units include a built-in motion sensor. For simplicity in this guide, references to the CLS-C6 unit apply equally to all, except where noted. Functional Summary · · · · · · · · · Automated control of up to six lighting loads: incandescent, magnetic low-voltage, neon/cold cathode, and non-dimmable lights Automated control of up to 16 shade and drape controllers, in up to six groups, for motorized window treatments, screens, and lifts Manual control of individual lighting loads and shade groups Versatile operation provides access to up to 16 stored scenes (lighting levels and shade position combinations) Built-in motion detector (CLS/CLSI-C6M units only) enables automated control based on room occupancy Built-in IR receiver allows wireless operation using an optional infrared remote control Multipoint control through up to 16 Crestron keypads (sold separately) allows control of rooms with several entrances or work areas Multi-unit expansion through support of up to eight additional CLSI-C6 units, enables systems of up to 54 lighting channels and 54 shade groups Control system integration via two separate Cresnet control networks; one for local devices and one for connection to a 2-Series control system All controls and indicators for the CLS -C6 are located on the front of the unit. The front panel also contains a mini phone jack, under the flip-up cover, used for dealer programming functions, and an IR port for control via an optional IR remote control. User Guide - DOC. [. . . ] In Standard mode and Lights mode, this button acts as lights master, adjusting all lighting loads simultaneously. In Shades mode, it adjusts all shade groups simultaneously. Function Buttons IR Receiver Label Strip Lights Pushbutton and LED Mini Phone Jack Motion Detector (CLS/CLSI-C6M only) OFF Button ON Button ^, v, Save, and Cancel Pushbuttons and LEDs Shades Pushbutton and LED Two-Digit Display Up/Down Pushbutton Operating Modes After installation, the CLS-C6 operates in one of three modes: · · · Standard mode: this is the default mode; buttons are typically used to recall scenes, although they can be reprogrammed by the dealer for other functions. Shades mode: this mode is used to manually control shade groups. The following descriptions do not include additional functionality made possible by dealer programming. Those functions are beyond the scope of this guide. User Guide - DOC. 6395A iLuxTM Lighting System: CLS/CLSI-C6 & CLS/CLSI-C6M · 3 iLuxTM Lighting System Crestron CLS/CLSI-C6 & CLS/CLSI-C6M Standard Mode By default, the six function buttons recall scenes 1 - 6. As a scene is recalled, the lights fade (change from one level to another) in a specified time, and any shades in the scene go to their specified levels. While fading, the LED for the selected scene recall button blinks, and then stays on when fade is complete; the two-digit display shows the time remaining; If you press the selected scene recall button again before fade is complete, the lights immediately go to their assigned levels and the LED turns solid. The six bargraphs always show the current level of each lighting load. When all lights are off, the LEDs for all function buttons glow dimly to make it easy to locate the panel in the dark. The Up/Down button acts as a lights master, adjusting the level of all dimmable lighting loads simultaneously. Pressing the top of the button raises the lights; pressing the bottom of the button lowers them. You can also select functions using an optional remote keypad or IR remote control. Lights Mode Lights mode lets you manually adjust any of the six lighting loads. The LED will light, and the six function buttons can now be used to adjust the six lighting loads. · · · Press the right side of the function buttons to raise the lights; press the left side to lower the lights. While a particular lighting load is being adjusted, the two-digit display shows its level. ("oF" indicates fully off; "on" indicates fully on; "1" ­ "99" indicate percent of the full on level. ) Press the center of a function button to check light level without adjusting. Press the top of the button to raise the lights; press the bottom of the button to lower the lights. · The ON and OFF buttons operate normally while in Lights mode. The LED will go off, and the unit will revert to Standard mode. Shades Mode Shades mode allows you to manually adjust any of the six shade groups. The LED will light, and the six function buttons can now be used to adjust shade groups 1 through 6. · · Press the right side of the function buttons to open the shades; press the left side to close the shades. [. . . ] If you would like a certain lighting load to be unaffected by that scene recall, press and hold the center of the button (so both sides make contact) for three seconds. The top two and the bottom two LEDs of the associated bargraph will be lit (and the display will show - -) to indicate that the level of the lighting load will not change when the scene is recalled. To change the shade presets for that scene press the Shades button; the Shades LED will be lit. Use the six function buttons to adjust the levels of the shade groups for that scene. [. . . ]