User manual CRESTRON TPS-XVGA

[. . . ] This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Crestron TPS-XVGA RGB Computer Interface Card for TPS/Tilt Panel Contents RGB Computer Interface Card for TPS/Tilt Panel: TPS-XVGA Description Functional Description Physical Description Leading Specifications Computer Video Connector Signals Preparation Installation and Hookup Touchpanel Setup Configuring the Touchpanel SIMPLTM Windows® Programming VT Pro-e Setup Problem Solving Troubleshooting Further Inquiries Future Updates Future Firmware Upgrades Appendix: Optional Touchpanel Setups Serial Mouse Control Driver Telestrator Video Annotation Device Return and Warranty Policies Merchandise Returns / Repair Service CRESTRON Limited Warranty 1 1 1 2 3 4 4 6 12 12 12 12 13 13 14 14 14 15 15 16 17 17 17 Operations & Installation Guide - DOC. 5944 RGB Computer Interface Card for TPS/Tilt Panel: TPS-XVGA · i Crestron TPS-XVGA RGB Computer Interface Card for TPS/Tilt Panel RGB Computer Interface Card for TPS/Tilt Panel: TPS-XVGA Description Functional Description The TPS-XVGA RGB computer interface card is an optional feature designed for Crestron's IsysTM TPS-5000 and TPS-6000 tilt touchpanels. Through an RGB window on a page within the uploaded VisionToolsTM Pro-e (VT Pro-e) touchpanel project, the card allows computer video to be displayed on the touchpanel full screen or in a window. [. . . ] Using a #1 Phillips screwdriver, loosen, remove and discard the two screws that secure the RGB port blank plate. From the inside of the touchpanel base, remove the plate and discard. Installation Diagram 3 of 7 - Remove RGB Port Blank Plate CAUTION: During the next step, to prevent tearing or distorting the touchpanel label, tighten the plate mounting screws only to the specification described. Hold the touchpanel base cover in place and position the touchpanel face-down onto a padded surface to prevent scratching of the screen. Re-install the eight base cover screws to finger-tight then, using a #1 Phillips screwdriver, tighten an additional 1/8-turn. NOTE: The TPS-IMC or optional TPS-IMW serves as an interface for the touchpanel. To connect the audio from the source computer to the touchpanel, consult the TPS-IMC or TPS-IMW Operations Guide (Doc. The latest revision can be obtained from the Products page (PRODUCT MANUALS section) or Downloads page (MANUAL Library) of Crestron's website (www. crestron. com). At the rear of the touchpanel base, attach a computer video cable (not supplied) from the computer video port to the RGB port of the touchpanel. If applicable, attach the audio cable connector from the TPS-IMC or optional TPS-IMW to the AUDIO port of the touchpanel. Installation Diagram 7 of 7 - Attach Computer Video Cable & Audio Cable AUDIO CABLE, IF APPLICABLE COMPUTER VIDEO CABLE HEADPHONES AUDIO RS-232 RGB NET/VIDEO LAN 24VDC 2. 0A 17. Re-connect any cables that were disconnected in step 2 to the appropriate ports on the rear of the touchpanel base. If the optional external power pack is utilized, connect the output plug of the power pack to the 24VDC 2. 0A port on the rear of the touchpanel base. Operations & Installation Guide - DOC. 5944 RGB Computer Interface Card for TPS/Tilt Panel: TPS-XVGA · 11 RGB Computer Interface Card for TPS/Tilt Panel Crestron TPS-XVGA Touchpanel Setup Configuring the Touchpanel To configure the touchpanel for RGB computer video input, consult the latest revision of the TPS-5000 or TPS-6000 Operations Guide (Doc. The latest version of the Operations Guide can be obtained from the Products page (PRODUCT MANUALS section) or the Downloads page (MANUAL Library) of Crestron's website (www. crestron. com). New users are required to register in order to obtain access to the FTP site. Upon entering the Setup Menu, an RGB button will be available and displayed. Selection of this button opens the RGB Menu from which RGB settings are adjusted. SIMPLTM Windows® Programming No special programming is required in SIMPL Windows for TPS-XVGA operation. NOTE: Join number remapping allows the Isys touchpanel to perform features in a new way. One group of features pertains specifically to use of the RGB Computer Interface Card. Refer to the latest revision of the Join Number Remapping Reference Guide (Doc. This document can be obtained from the Downloads page (MANUAL Library, search for JNR. PDF) of Crestron's website (www. crestron. com). VT Pro-e Setup In order for the RGB video to be displayed, the TPS-XVGA must be installed into the proper expansion slot of the TPS-5000 or TPS-6000 and a RGB window object must reside on a page within the uploaded VT Pro-e touchpanel project. If the card is not present, the Viewport will display a warning message during the upload and the RGB window would be blank. For details regarding RGB window objects, refer to the VT Pro-e help file. 12 · RGB Computer Interface Card for TPS/Tilt Panel: TPS-XVGA Operations & Installation Guide - DOC. [. . . ] To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ]