User manual CRESTRON TPS-XTXRF

[. . . ] This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Crestron TPS-XTXRF Two-Way RF Transceiver Module Contents Two-Way RF Transceiver Module: TPS-XTXRF 1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Physical Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To configure a TPS-RFGWX Two-Way RF Transceiver (sold separately), refer to the latest revision of the TPS-RFGWX Operations & Installation Guide (Doc. This document can be obtained from the Downloads | Product Manuals section of the Crestron website (www. crestron. com). Example Program The TPS-XTXRF equipped touchpanel communicates to a TPS-RFGWX Two-Way RF Transceiver (sold separately) that resides on the Cresnet system. The TPS-XTXRF equipped touchpanel and TPS-RFGWX may be programmed similar to (operating frequencies are not compatible) the STRFGWX Two-Way RF Transceiver and STX-1550C two-way wireless RF touchpanel. For an example program, refer to the program for the STX-1550C which is available from the Crestron FTP site (www. ftp. crestron. com). Select the Examples folder and search for STX1550C_*. SMW. Configuring the Touchpanel for Operation The touchpanel with the TPS-XTXRF installed can operate as a Cresnet or RF device. The operation of the touchpanel is determined by the attachment of the NET/VIDEO cable to the touchpanel. To use the touchpanel as a Cresnet wired unit, connect the NET/VIDEO cable to the NET/VIDEO port of the touchpanel. To use the touchpanel as an RF unit, disconnect the cable from the touchpanel. In summary, the RF-enabled touchpanel can only operate in one mode of operation at a time and the mode is determined by whether a connection is made at the NET/VIDEO port. NOTE: If the intent is to use the touchpanel in both modes, Crestron recommends that the programmer does not comment out the Cresnet ID of the touchpanel in the SIMPL Windows program. If the ID is commented out, the touchpanel will cease to operate when the NET/VIDEO cable is connected. To configure the unit, it may be necessary to access a series of setup screens prior to viewing run-time screens that are loaded into the touchpanel for normal Cresnet or RF operation. The next two sections provide details regarding configuration of the touchpanel for both modes of operation. Cresnet Configuration For configuration of the touchpanel with respect to Cresnet mode of operation, consult the appropriate IsysTM tilt touchpanel operations guide. This document can be obtained from the Downloads | Product Manuals section of the Crestron website (www. crestron. com). It provides details about setting the Cresnet ID of the touchpanel as well as setting up the touchpanel for Ethernet or RS-232 communication, displaying computer-generated video format (RGB) and video from up to two different sources, adjusting audio controls, and selecting personal setting for screen brightness and timeouts. Operations & Installation Guide - DOC. 5844 Two-Way RF Transceiver Module: TPS-XTXRF · 15 Two-Way RF Transceiver Module RF Configuration Crestron TPS-XTXRF Crestron IsysTM tilt touchpanel are default configured for Cresnet (wired) operation. To configure the TPS-XTXRF equipped touchpanel for RF communication, it is necessary to access a series of setup screens on the touchpanel. NOTE: For additional touchpanel configuration information, consult the appropriate IsysTM tilt touchpanel operations guide. This document can be obtained from the Downloads | Product Manuals section of the Crestron website (www. crestron. com). The Main Menu for configuring the touchpanel appears when a finger is held to the touchscreen as power is applied. Remove your finger after approximately 3 to 5 seconds when the message "SETUP MODE" appears on the touchscreen. 4. Interface Menu 5. On Interface Menu, select the RF Enable button. NOTE: To ensure communication between the TPS-RFGWX and RF-enabled touchpanel, distinct types of identification codes are required. [. . . ] Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. [. . . ]