User manual CRESTRON TPS-XBTP

[. . . ] 5845 Battery Pack for TPS-XTXRF: TPS-XBTP · 1 Battery Pack for TPS-XTXRF Crestron TPS-XBTP Physical Description The TPS-XBTP is housed in a black enclosure with its electrical contacts located on the bottom (see views below). TPS-XBTP Top, Side & Rear Views 5. 00 in (12. 70 cm) 7. 14 in (18. 14 cm) 1. 40 in (3. 56 cm) TPS-XBTP Bottom View ELECTRICAL CONTACTS 2 · Battery Pack for TPS-XTXRF: TPS-XBTP NICKEL-MH BATTERY: MUST BE RECYCLED OR DISPOSED OF PROPERLY. CAUTION DO NOT BURN OR PUNCTURE BATTERY. 5845 Crestron TPS-XBTP Battery Pack for TPS-XTXRF Leading Specifications The following table provides a summary of leading specifications for the TPS-XBTP. Leading Specifications for the TPS-XBTP SPECIFICATION Output Voltage Composition Estimated Operating Time, (new unit with full charge) Estimated Life Optimal Operating Temperature Optimal Storage Temperature DETAILS 20 VDC (4. 5 Ah), nominal Nickel-metal hydride (Ni-MH) Approximately 2-hours with typical use, (8 -10 hours in touchpanel stand-by) * 500 charging/discharging cycles Approximately 32oF to 104oF (0oC to +40oC) Approximately -4oF to 113oF (-20oC to +45oC) Approximately 50oF to 95oF (10oC to 35oC) 2. 20 lb (1. 00 kg) Charging Temperature Weight * Approximate battery life and charge times for Battery pack in touchpanels: Worst case battery life - TPS-6000 with all 3 cards installed is 2 hours at full backlight Best case battery life - TPS-4500 with no cards installed is 3. 5 hours at full backlight Worst case charge time - TPS-6000 with all 3 cards installed is 12 hours Best case charge time - All units with power off is 3. 5 hours NOTE: The battery will not charge when hot. To cool the battery, either turn off power to the Touchpanel by pressing the power down button on the touchscreen (or use the power down timeout), or remove the battery from the touchpanel. [. . . ] After an extended storage, allow the battery pack to obtain room temperature, discharge fully, and charge to restore full capacity. When storing battery pack for more than 1-year, charge at least once a year to prevent leakage and deterioration in performance due to self-discharging. 4 · Battery Pack for TPS-XTXRF: TPS-XBTP Operations and Installation Guide - DOC. 5845 Crestron TPS-XBTP Battery Pack for TPS-XTXRF Charging & Discharging NOTE: Typically, the battery pack is good for 500 charge/discharge cycles. Charging To charge the TPS-XBTP: · Use the TPS-XBC Battery Charger; or · Install the TPS-XBTP in a TPS-XTXRF equipped touchpanel that is docked to a powered TPS-XDS Docking Station. NOTE: An external power pack or Cresnet power connected directly to the TPS-XTXRF equipped touchpanel does NOT charge the TPS-XBTP. The latest versions of the guides are available from the Downloads | Product Manuals section of the Crestron website (www. crestron. com). If you think that the touchpanel's level indicator is inaccurate, you may need to discharge the battery. For example, the level indicator may read 80%, even though the charge LED on the TPS-XDS goes out (indicating a full charge). To discharge, insert the battery pack in an undocked TPS-XTXRF equipped touchpanel, and allow the touchpanel to remain ON until it no longer operates and/or the control system power/battery gauge indicates minimum. NOTE: After fully discharging the battery, fully charge the battery (see Charging instructions above). NOTE: The battery pack discharges at a rate of 25% per month when not used, which may cause an inaccurate reading on the level indicator. Operations and Installation Guide - DOC. 5845 Battery Pack for TPS-XTXRF: TPS-XBTP · 5 Battery Pack for TPS-XTXRF Crestron TPS-XBTP Installation The TPS-XBTP is designed to prevent improper installation. The unit fits only one way in the battery compartment of a touchpanel equipped with the TPS-XTXRF. Note the bottom-center slot of the TPS-XTXRF and insert the battery pack in the touchpanel until it snaps in place. Insert TPS-XBTP into Touchpanel 6 · Battery Pack for TPS-XTXRF: TPS-XBTP Operations and Installation Guide - DOC. 5845 Crestron TPS-XBTP Battery Pack for TPS-XTXRF Removal To remove the TPS-XBTP from a touchpanel equipped with the TPS-XTXRF, press down the battery eject button, allow the battery pack to eject approximately 1/4-inch and remove the pack. See diagram below. TPS-XBTP removal from rear of touchpanel Operations and Installation Guide - DOC. 5845 Battery Pack for TPS-XTXRF: TPS-XBTP · 7 Battery Pack for TPS-XTXRF Crestron TPS-XBTP Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. For assistance in your local time zone, refer to the Crestron website (www. crestron. com) for a listing of Crestron's worldwide offices. [. . . ] Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. [. . . ]