User manual CRESTRON TPS-VIDL

[. . . ] 5830 Video Card for TPS/Lectern Panel: TPS-VIDL · 1 Video Card for TPS/Lectern Panel TPS-VIDL Top View Crestron TPS-VIDL 2. 63 in (6. 67 cm) 5. 00 in (12. 70 cm) Leading Specifications The table below provides a summary of leading specifications for the TPS-VIDL. Dimensions and weight are rounded to the nearest hundredth unit. Leading Specifications of the TPS-VIDL SPECIFICATION Power Requirements Video Types Video Formats Video Format Detection SIMPLTM Windows® DETAILS 24VDC Cresnet power, load factor of 8 Watts. Version 1. 40. 07 or later 1 with the addition of smwlib89. exe and smwlib89. txt. 2 Height: 1. 16 in (2. 95 cm) Width: 2. 63 in (6. 67 cm) Depth: 5. 00 in (12. 70 cm) Weight: 3. 20 oz (0. 09 kg) CNMXSX-AV/Pro Update File CNRACKX/-DP Update File Dimensions & Weight 1 The latest software version can be obtained from the Downloads page (SIMPLWIN Library) of Crestron's website (www. crestron. com). [. . . ] To prevent scratching of the screen (TPS-TPI excluded), place the touchpanel face-down onto a padded surface. Operations & Installation Guide - DOC. 5830 Video Card for TPS/Lectern Panel: TPS-VIDL · 3 Video Card for TPS/Lectern Panel Crestron TPS-VIDL 2. Using a #1 Phillips screwdriver, loosen and remove the 10 screws that secure the touchpanel rear cover. Remove Touchpanel Rear Cover Screws CAUTION: The connectors of any optional card that is already installed may have to be aligned slightly to allow the rear cover to be removed. Align the connectors carefully to prevent damage to the card, cover, or touchpanel. Remove the touchpanel rear cover by sliding it towards the bottom of the touchpanel as shown below. Remove Touchpanel Rear Cover 4 · Video Card for TPS/Lectern Panel: TPS-VIDL Operations & Installation Guide - DOC. Using a #1 Phillips screwdriver, loosen and remove the two screws that secure the PCB blank plate and remove the plate. Remove PCB Blank Plate 5. As shown below, align the pins on the touchpanel interface connector of the TPS-VIDL with the touchpanel motherboard connector. Install TPS-VIDL 6. Make sure that the mounted screws align with mounting posts of the motherboard. Tighten the card mounting screws to finger-tight. Operations & Installation Guide - DOC. 5830 Video Card for TPS/Lectern Panel: TPS-VIDL · 5 Video Card for TPS/Lectern Panel Crestron TPS-VIDL CAUTION: The TPS-VIDL connectors may have to be aligned slightly to fit through the openings in the rear cover. Align the connectors of this card (or any other optional card that is installed) carefully to prevent damage to the card, cover, or touchpanel. As shown below, install the touchpanel rear cover by sliding it over the TPS-VIDL connectors. Install Touchpanel Rear Cover 9. Using a #1 Phillips 1/4-inch hex bit and an inchpound torque driver, install 10 screws and tighten to 4-inch pounds (0. 45 Newton-meters) to secure cover. Install Touchpanel Rear Cover Screws 6 · Video Card for TPS/Lectern Panel: TPS-VIDL Operations & Installation Guide - DOC. 5830 Crestron TPS-VIDL Video Card for TPS/Lectern Panel NOTE: Depending upon the individual installation, video connectors #1 or #2 may be used. The input signals are identical, only the connector type is different. Refer to the diagram below and make the appropriate S-video or composite video connection(s) as shown. Attach Appropriate Video Cables VIDEO CONNECTORS #1 VIDEO CONNECTORS #2 { C COMP Y FROM S-VIDEO LUMINANCE OR COMPOSITE VIDEO OUTPUT C Y + -S+ -S FROM S-VIDEO CHROMINANCE OUTPUT NOTE: Refer to the latest revision of the TPS-5000L, TPS-6000L, or TPS-TPI Operations & Installation Guide (Doc. 5825, 5783, or 5855, respectively) or, if applicable, BB-5000 or BB-6000 Installation Guide (Doc. 5826 or 5827, respectively) for the proper installation procedure of the touchpanel. The latest software version of the Operations & Installation Guides can be obtained from the Downloads page (MANUAL Library) of Crestron's website (www. crestron. com). NOTE: Refer to the latest revision of the TPS-5000L, TPS-6000L, or TPS-TPI Operations & Installation Guide (Doc. [. . . ] Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. [. . . ]