User manual CRESTRON TPS-VID

[. . . ] 5869A Video Card for TPS/Tilt Panel: TPS-VID · 1 Video Card for TPS/Tilt Panel Crestron TPS-VID NOTE: For more information about the Crestron TPS interface or wallmounted interface module(s), refer to the latest revision of the appropriate operations guide. The latest version can be obtained from the Products page (PRODUCT MANUALS, Hardware section) or Downloads page (MANUAL Library) of Crestron's website (www. crestron. com). New users are required to register in order to obtain access to the FTP site. Physical Description The TPS-VID card, shown in the two diagrams below, is a printed circuit board (PCB) designed to be installed into a specific expansion slot on the touchpanel motherboard. The card contains a 60-pin connector that attaches directly to the motherboard and the card is secured with four mounting screws (supplied with TPS-VID). [. . . ] READ INSTRUCTION MANUAL BEFORE OPERATING NO USER SERVICABLE PARTS UNDER THIS COVER ELECTRONICS, INC Rockleigh, NJ 07647 U. S. A. FCC ID: EROTPS-6000 SEE MANUAL USE POWER PACK PW-2420RU TPS-6000 ZA***** C000000 6. As shown on the next page, remove the touchpanel base cover by raising it upwards and rearward. Operations & Installation Guide - DOC. 5869A Video Card for TPS/Tilt Panel: TPS-VID · 5 Video Card for TPS/Tilt Panel Crestron TPS-VID TPS-VID Installation (2 of 6) - Remove Touchpanel Base Cover 8. As shown below, align the pins on the touchpanel interface connector of the TPS-VID with the touchpanel motherboard connector. Make sure that the screw holes of the card align with the mounting posts on the motherboard. TPS-VID Installation (3 of 6) - Install TPS-VID 6 · Video Card for TPS/Tilt Panel: TPS-VID Operations & Installation Guide - DOC. Install the four card mounting screws (supplied), tighten to finger-tight then, using a Philips screwdriver, tighten an additional 1/8-turn. TPS-VID Installation (4 of 6) - Install TPS-VID Mounting Screws 10. Position the touchpanel base cover onto the base by tilting the front of the cover downward under the touchpanel pivot and lowering. Hold the touchpanel base cover in place and position the touchpanel face-down onto a padded surface to prevent scratching of the screen. Re-install the eight base cover screws to finger-tight then, using a Philips screwdriver, tighten an additional 1/8-turn. Operations & Installation Guide - DOC. 5869A Video Card for TPS/Tilt Panel: TPS-VID · 7 Video Card for TPS/Tilt Panel Crestron TPS-VID TPS-VID Installation (5 of 6) - Re-install Touchpanel Base Cover Screws CLEAN PANEL WITH SOFT CLOTH ONLY ELECTRONICS, INC Rockleigh, NJ 07647 U. S. A. READ INSTRUCTION MANUAL BEFORE OPERATING NO USER SERVICABLE PARTS UNDER THIS COVER ELECTRONICS, INC Rockleigh, NJ 07647 U. S. A. FCC ID: EROTPS-6000 SEE MANUAL USE POWER PACK PW-2420RU TPS-6000 ZA***** C000000 NOTE: The table below is provided as reference information about the pinouts of the NET/VIDEO connector. TYPE 10-position RJ45 PIN DESIGNATION DESCRIPTION 1* Power (Network) +24V 2 Ground (Network) GND 3 Chrominance (Positive) C+ 4 Chrominance (Negative) C5 Data (Network) Y 6 Z Data (Network) Luminance (Positive)/Composite 7 Y+ Luminance (Negative)/Composite 8 Y9 GND Ground (Network) +24V Power (Network) 10 * While facing the NET/VIDEO port of the touchpanel, pin 1 is located at the upperleft of the port. 13. Refer to the diagram on the next page for the video connector signals and attach the 10-position net/video cable assembly or net/video connector of triamese (three shielded cables within a single jacket) cable assembly supplied with TPS-IMC-BV to the NET/VIDEO port of the touchpanel. Connect the other end of the cable assembly to the NET/VIDEO port of the appropriate interface module (TPS-IMC is shown). 8 · Video Card for TPS/Tilt Panel: TPS-VID Operations & Installation Guide - DOC. 5869A Crestron TPS-VID Video Card for TPS/Tilt Panel NOTE: When connecting the video from the interface module to the touchpanel, exceeding a video cable length 30-feet will significantly degrade the video signal. If further assistance is required, please contact a Crestron customer service representative. TPS-VID Troubleshooting TROUBLE Video window of touchpanel has no display. POSSIBLE CAUSE(S) Improper video connection. Incorrect video cable used. CORRECTIVE ACTION Verify proper connections at touchpanel NET/VIDEO port. Verify that the 10-position Net/Video cable assembly is used to connect the NET/VIDEO port of the touchpanel to the TPS-IMC (or equivalent). Select proper video format or autodetect in touchpanel configuration setup menu. Update firmware/software versions as per "Leading Specifications". Make sure that video window object resides in project, re-compile, and reload. [. . . ] Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supercedes all previous warranties. Trademark Information All brand names, product names, and trademarks are the sole property of their respective owners. Windows95/98/Me and WindowsNT/2000 are trademarks of Microsoft Corporation. 12 · Video Card for TPS/Tilt Panel: TPS-VID Operations & Installation Guide - DOC. [. . . ]