User manual CRESTRON TPS-IMPC

[. . . ] An AC adapter port, network connector, and video input connectors are located on one side of the unit. The opposite side provides a video input signal selector switch, audio input connectors, microphone output connectors, and audio/network/video connections to the touchpanel. The TPS-IMPC also has mounting feet to secure the unit to a mounting surface. Physical Views of the TPS-IMPC 5. 32 in (13. 52 cm) 0. 25 in (0. 64 cm) 5. 82 in (14. 78 cm) 3. 50 in (8. 89 cm) 2. 81 in (7. 12 cm) 1. 14 in (2. 89 cm) 1. 12 in (2. 84 cm) Ø 0. 16 in (0. 41 cm) 6 PLACES 0. 27 in (0. 69 cm) THESE DIMENSIONS ARE THE SAME FOR BOTH SIDES OF THE UNIT 1. 25 in (3. 18 cm) Ports There are nine ports that serve various functions on the TPS-IMPC. [. . . ] As long as a switch is in the appropriate position, a signal can be connected to either the BNC or twisted-pair connector. To select the twisted pair connector for balanced video, the DIP switch for the respective video source must be in the "UP" position. To use the coaxial connector(s) for unbalanced video, the DIP switch must be in the "DOWN" position. 6 · Interface Module: TPS-IMPC Operations Guide - DOC. 6162 Crestron TPS-IMPC Interface Module Industry Compliance As of the date of manufacture, the TPS-IMPC has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling (N11785). Setup Network Wiring CAUTION: Use only Crestron power supplies for Crestron equipment. Failure to do so could cause equipment damage or void the Crestron warranty. NOTE: When installing network wiring, refer to the latest revision of the wiring diagram(s) appropriate to your specific system configuration, available from the Downloads | Product Manuals | Wiring Diagrams section of the Crestron website (www. crestron. com). Care should be taken to ensure data (Y, Z) and power (24, G) connections are not crossed. One twisted pair is the +24V conductor and the GND conductor and the other twisted pair is the Y conductor and the Z conductor. NOTE: For larger networks (i. e. , greater than 28 network devices), it may be necessary to add a Cresnet Hub/Repeater (CNXHUB) to maintain signal quality throughout the network. Also, for networks with lengthy cable runs or varying types of network devices, it may be desirable to add a hub/repeater after only 20 network devices. When calculating the wire gauge for a particular network run, the length of the run and the power factor of each network unit to be connected Operations Guide - DOC. 6162 Interface Module: TPS-IMPC · 7 Interface Module Crestron TPS-IMPC must be taken into consideration. If network units are to be daisy-chained on the run, the power factor of each network unit to be daisy-chained must be added together to determine the power factor of the entire chain. The length of the run in feet and the power factor of the run should be used in the following resistance equation to calculate the value on the right side of the equation. Resistance Equation R < 40, 000 L x PF Where: R = Resistance (refer to table below). PF = Power factor of entire run (or chain). The required wire gauge should be chosen such that the resistance value is less than the value calculated in the resistance equation. As older AUDIO cables may not have the blue cover, be sure to insert the AUDIO cable into the AUDIO port. NOTE: Do not confuse the 8-pin audio cable with the 10-pin net/video cable. Operations Guide - DOC. 6162 Interface Module: TPS-IMPC · 9 Interface Module Crestron TPS-IMPC Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. TPS-IMPC Troubleshooting TROUBLE Touchpanel does not function. POSSIBLE CAUSE(S) Touchpanel is not receiving power. CORRECTIVE ACTION Confirm that power is supplied via the power pack or the Cresnet connector (not both). Replace the 8-pin audio cable with the 10-pin net/video cable. Touchpanel is not communicating to the network. [. . . ] Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supercedes all previous warranties. Trademark Information All brand names, product names, and trademarks are the sole property of their respective owners. [. . . ]