User manual CRESTRON TPS-IMC

[. . . ] 7 Further Inquiries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Return and Warranty Policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Merchandise Returns / Repair Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 CRESTRON Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Refer to the descriptions and pinout table that follow this paragraph. This port also makes available composite and S-video input for TV video card (with the purchase and installation of the TPS-VID). Consult the latest revision of the TPS-VID Operations & Installation Guide (Doc. 5869) for details. NET/VIDEO Pinouts PIN # 1 2 3 4 5 6 7 8 9 10 DESIGNATION +24V GND C+ CY Z Y+ YGND +24V DESCRIPTION Power (Network) Ground (Network) Chrominance (Positive) Chrominance (Negative) Data (Network) Data (Network) Luminance (Positive)/Composite Luminance (Negative)/Composite Ground (Network) Power (Network) · MIC OUT ­ The port mates with a three-pin connector, supplied, and produces line level differential output. Description of the pinouts is shown in the table after this paragraph. MICROPHONE Pinouts PIN M+ MS DESCRIPTION Positive Negative Shield · AUDIO INPUT ­ The port mates with a six-pin connector, supplied, and provides differential/single ended audio input and output. Description of the pinouts is shown in the table after this paragraph. AUDIO INPUT Pinouts PIN S R+ RL+ LS DESCRIPTION Shield Right Positive Right Negative Left Positive Left Negative Shield Operations Guide - DOC. 5856 Interface Module: TPS-IMC · 3 Interface Module Crestron TPS-IMC Leading Specifications The table after this paragraph provides a summary of leading specifications for the TPS-IMC. Dimensions and weight are rounded to the nearest hundredth unit. Leading Specifications for the TPS-IMC SPECIFICATION Dimensions DETAILS Height: 2. 00 in (5. 08 cm) Width: 5. 33 in (13. 53 cm) Depth: 1. 24 in (3. 15 cm) Weight 0. 59 lb (0. 27 kg) As of the date of manufacture, the TPS-IMC has been tested and found to comply with specifications for CE marking. Setup Network Wiring NOTE: When making wire connections, refer to the latest revision of the Cresnet Network Interconnect Drawing (Doc. The document can be obtained from the Downloads page (CABLES and MANUAL Libraries) of the Crestron website (www. When calculating the wire gauge for a particular network run, the length of the run and the power factor of each network unit to be connected must be taken into consideration. If network units are to be daisy-chained on the run, the load factor of each network unit to be daisy-chained must be added together to determine the load factor of the entire chain. The length of the run in feet and the load factor of the run should be used in the following resistance equation to calculate the value on the right side of the equation. Resistance Equation R < 40, 000 L x LF Where: R = Resistance (refer to table below). LF = Load factor of entire run (or chain). The required wire gauge should be chosen such that the resistance value is less than the value calculated in the resistance equation. Refer to the table after this paragraph. Wire Gauge Values RESISTANCE (R) 4 6 10 15 WIRE GAUGE 16 18 20 22 13 24 (Doubled-CAT 5) 4 · Interface Module: TPS-IMC Operations Guide - DOC. 5856 Crestron TPS-IMC Interface Module NOTE: All network wiring must consist of two twisted-pairs. One twisted pair is the +24V conductor and the GND conductor and the other twisted pair is the Y conductor and the Z conductor. NOTE: When daisy chaining network units, always twist the ends of the incoming wire and outgoing wire which share a pin on the network connector. Avoid tinning too far up or the tinned end becomes brittle and breaks. After tinning the twisted ends, insert the tinned connection into the network connector and tighten the retaining screw. Repeat the procedure for the other three network conductors. Hardware Hookup The TPS-IMC serves as an interface between the touchpanel and the Cresnet system. Refer to the illustration after this paragraph (which continues on next page) for proper connections; apply power last. When making network connections to the CNX Generation control system or Cresnet peripherals, refer to the latest revision of the Cresnet Network Interconnect Drawing (Doc. [. . . ] CRESTRON shall, at its option, repair or replace any product found defective without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. CRESTRON shall not be liable to honor warranty terms if the product has been used in any application other than that for which it was intended, or if it has been subjected to misuse, accidental damage, modification, or improper installation procedures. Furthermore, this warranty does not cover any product that has had the serial number altered, defaced, or removed. [. . . ]