User manual CRESTRON TPS-4500IMPC

[. . . ] The opposite side provides a video input signal selector switch, and network/video connections to the touchpanel. The TPS-4500IMPC also has mounting feet to secure the unit to a mounting surface. Physical Views of the TPS-4500IMPC SIDE VIEW ROTATED 180° 5. 82 in 5. 32 in (14. 78 cm) (13. 52 cm) 0. 25 in (0. 64 cm) 3. 50 in (8. 89 cm) 2. 81 in (7. 12 cm) 1. 14 in (2. 89 cm) 1. 12 in (2. 84 cm) Ø 0. 16 in (0. 41 cm) 6 PLACES 0. 27 in (0. 69 cm) THESE DIMENSIONS ARE THE SAME FOR BOTH SIDES OF THE UNIT 1. 25 in (3. 18 cm) Ports There are five ports that serve various functions on the TPS-4500IMPC. Refer to the following diagrams and descriptions of each port. 2 · Interface Module: TPS-4500IMPC Operations Guide - DOC. [. . . ] As long as a switch is in the appropriate position, a signal can be connected to either the BNC or twisted-pair connector. To select the twisted pair connector for balanced video, the DIP switch for the respective video source must be in the "UP" position. To use the coaxial connector(s) for unbalanced video, the DIP switch must be in the "DOWN" position. Industry Compliance As of the date of manufacture, the TPS-4500IMPC has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling (N11785). Setup Network Wiring CAUTION: Use only Crestron power supplies for Crestron equipment. Failure to do so could cause equipment damage or void the Crestron warranty. Operations Guide - DOC. 6163 Interface Module: TPS-4500IMPC · 5 Interface Module Crestron TPS-4500IMPC CAUTION: Possible equipment damage if miswired. NOTE: When installing network wiring, refer to the latest revision of the wiring diagram(s) appropriate to your specific system configuration, available from the Downloads | Product Manuals | Wiring Diagrams section of the Crestron website (www. crestron. com). Care should be taken to ensure data (Y, Z) and power (24, G) connections are not crossed. One twisted pair is the +24V conductor and the GND conductor and the other twisted pair is the Y conductor and the Z conductor. NOTE: For larger networks (i. e. , greater than 28 network devices), it may be necessary to add a Cresnet Hub/Repeater (CNXHUB) to maintain signal quality throughout the network. Also, for networks with lengthy cable runs or varying types of network devices, it may be desirable to add a hub/repeater after only 20 network devices. When calculating the wire gauge for a particular network run, the length of the run and the power factor of each network unit to be connected must be taken into consideration. If network units are to be daisy-chained on the run, the power factor of each network unit to be daisy-chained must be added together to determine the power factor of the entire chain. The length of the run in feet and the power factor of the run should be used in the following resistance equation to calculate the value on the right side of the equation. Resistance Equation R < 40, 000 L x PF Where: R = Resistance (refer to table below). PF = Power factor of entire run (or chain). The required wire gauge should be chosen such that the resistance value is less than the value calculated in the resistance equation. Refer to the following table. 6 · Interface Module: TPS-4500IMPC Operations Guide - DOC. 6163 Crestron TPS-4500IMPC Wire Gauge Values RESISTANCE (R) 4 6 10 15 13 8. 7 Interface Module WIRE GAUGE 16 18 20 22 Doubled CAT5 Tripled CAT5 NOTE: When daisy-chaining Cresnet units, strip the ends of the wires carefully to avoid nicking the conductors. Twist together the ends of the wires that share a pin on the network connector, and tin the twisted connection. Insert the tinned connection into the Cresnet connector and tighten the retaining screw. Repeat the procedure for the other three conductors. Hardware Hookup The TPS-4500IMPC serves as an interface between the touchpanel and the Cresnet system. Refer to the illustration after this paragraph for proper connections; apply power last. When making network connections to a control system or Cresnet peripherals, refer to "Network Wiring" on page 5. [. . . ] CRESTRON is not liable for any claim made by a third party or made by the purchaser for a third party. CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. [. . . ]