User manual CRESTRON TPS-4500IMC

[. . . ] 8 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Further Inquiries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Future Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Return and Warranty Policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Consult the latest revision of the TPS-VID Operations & Installation Guide (Doc. NET/VIDEO Pinouts PIN # DESIGNATION 1 2 3 4 5 6 7 8 9 10 +24V GND C+ CY Z Y+ YGND +24V DESCRIPTION Power (Network) Ground (Network) Chrominance (Positive) Chrominance (Negative) Data (Network) Data (Network) Luminance (Positive)/Composite Luminance (Negative)/Composite Ground (Network) Power (Network) Leading Specifications The table after this paragraph provides a summary of leading specifications for the TPS-4500IMC. Leading Specifications for the TPS-4500IMC SPECIFICATION DETAILS Dimensions Height: 2. 00 in (5. 08 cm) Width: 5. 33 in (13. 53 cm) Depth: 1. 24 in (3. 15 cm) 0. 51 lb (0. 23 kg) Weight As of the date of manufacture, the TPS-4500IMC has been tested and found to comply with specifications for CE marking. Operations Guide - DOC. 5890 Interface Module: TPS-4500IMC · 3 Interface Module Crestron TPS-4500IMC Setup Network Wiring NOTE: When making wire connections, refer to the latest revision of the Cresnet Network Interconnect Drawing (Doc. The document can be obtained from the Downloads page (CABLES and MANUAL Libraries) of the Crestron website (www. When calculating the wire gauge for a particular network run, the length of the run and the power factor of each network unit to be connected must be taken into consideration. If network units are to be daisy-chained on the run, the load factor of each network unit to be daisy-chained must be added together to determine the load factor of the entire chain. The length of the run in feet and the load factor of the run should be used in the following resistance equation to calculate the value on the right side of the equation. Resistance Equation R < 40, 000 L x LF Where: R = Resistance (refer to table below). LF = Load factor of entire run (or chain). The required wire gauge should be chosen such that the resistance value is less than the value calculated in the resistance equation. Wire Gauge Values RESISTANCE (R) 4 6 10 15 13 WIRE GAUGE 16 18 20 22 24 (Doubled-CAT 5) NOTE: All network wiring must consist of two twisted-pairs. One twisted pair is the +24V conductor and the GND conductor and the other twisted pair is the Y conductor and the Z conductor. 4 · Interface Module: TPS-4500IMC Operations Guide - DOC. 5890 Crestron TPS-4500IMC Interface Module NOTE: When daisy chaining network units, always twist the ends of the incoming wire and outgoing wire which share a pin on the network connector. Avoid tinning too far up or the tinned end becomes brittle and breaks. After tinning the twisted ends, insert the tinned connection into the network connector and tighten the retaining screw. Repeat the procedure for the other three network conductors. Hardware Hookup The TPS-4500IMC serves as an interface between the touchpanel and the Cresnet system. Refer to the illustration on the next page for proper connections; apply power last. When making network connections to the CNX Generation control system or Cresnet peripherals, refer to "Network Wiring" on page 4 for details. It is not necessary to make connections to a video source unless the TPS-VID has been installed into the touchpanel and a video window object resides on a page within the uploaded VisionToolsTM Pro-e project. Operations Guide - DOC. 5890 Interface Module: TPS-4500IMC · 5 Interface Module Hardware Hookup for the TPS-4500IMC CONNECT TO TPS-4500 Crestron TPS-4500IMC CRESTRON TPS -4500 IMC NTSC/PAL VIDEO NET 24 Y Z G COMP Y C COMP Y C _S+_S + CONNECT TO CNX GENERATION CONTROL SYSTEM OR CRESNET PERIPHERALS * Connect to a video source only if the TPS-VID expansion card is installed in the touchpanel. The BNC connector and screw terminal mini Phoenix connector is connected in parallel. Possible options are no connection, balance video using twisted pair cable, or unbalanced video using coax cable. [. . . ] CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. [. . . ]