User manual CRESTRON ST-1700C PRE-SILVER

[. . . ] Crestron ST-1700C 1-Way Wireless RF Touchpanel Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2002 Crestron Electronics, Inc. Crestron ST-1700C 1-Way Wireless RF Touchpanel Contents 1-Way Wireless RF Touchpanel: ST-1700C 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The PRO2 with its associated communication ports is displayed in the System Views upper pane. PRO2 System View The System Views lower pane displays the PRO2 system tree. This tree can be expanded to display and configure the communications ports. Expanded PRO2 System Tree C2Net-Device Slot in Configuration Manager To incorporate a wireless RF touchpanel into the system, a gateway device is required. Once a gateway is configured in a C2Net-Device Slot, the slot allows Cresnet communication between the touchpanel and the control system. In Configuration Manager, drag the CNRFGWA gateway from the Wireless Receivers (RF) folder of the Device Library. The System Views upper pane displays the CNRFGWA device icon below the PRO2 graphic. NOTE: An ST-CP control processor is automatically configured with a CNRFGWA in its STCP-Net Device Slot 3, with a fixed NET ID of 2, when the ST-CP is dragged into the upper pane of System Views. Drag the ST-1700C from the Touchpanels (Wireless | Wireless one way) folder of the Device Library and drop it on the CNRFGWA symbol in System Views. The PRO2 system tree displays the CNRFGWA gateway in Slot 9, with a default NET ID of 24. The CNRFGWA displays the touchpanel at the touchpanel's default RF ID location, "10, " as shown in the following illustration. Operations Guide ­ DOC. 6050 1-Way Wireless RF Touchpanel: ST-1700C · 19 1-Way Wireless RF Touchpanel C2Net Device, Slot 9 Crestron ST-1700C Double-click the CNRFGWA icon in the upper pane to open the "Device Settings" window. Select the Net ID tab to change the gateway Net ID, as shown in the following figure. "Device Settings" Window for the CNRFGWA NOTE: Recall that if the CNRFGWA is part of an ST-CP configuration, its NET ID is fixed at 02 and cannot be changed. Similarly, expand the system tree in the lower pane and double-click the ST-1700C icon to open the "Device Settings" window for the touchpanel. Select the RF/IR ID tab to change the touchpanel RF ID, as shown in the following figure. For more information on setting the RF/IR ID, see "Select Interface on page 8. Although the device setting window in SIMPL Windows allows choices through the range of twodigit Hexadecimal numbers from 01 through FE, the RF ID setting for the hardware is limited to numbers in increments of the most significant digit (i. e. , 00, 10, 20). Since 00 is not a valid selection in SIMPL Windows, the RF ID number is limited to the fifteen numbers 10, 20, 30, 40, . . F0. 20 · 1-Way Wireless RF Touchpanel: ST-1700C Operations Guide ­ DOC. 6050 Crestron ST-1700C 1-Way Wireless RF Touchpanel Touchpanel "Device Settings" Window ST-1700C Symbol in Programming Manager Programming Manager is where programmers "program" a Creston control system by assigning signals to symbols. The following diagram shows the ST-1700C symbol in the SIMPL Windows' Programming Manager. Detail View of the ST-1700C in SIMPL Windows' Programming Manager NOTE: Join numbers are expandable to 999. The table below lists and gives functional descriptions for the touchpanel outputs. Symbol Output Signal Descriptions OUTPUT press 1 through press 32* DESCRIPTION Notifies control system of button press (1 ­ 32*). High/1 = button is being pressed Low/0 = button is not being pressed *Expandable to 999 Operations Guide ­ DOC. 6050 1-Way Wireless RF Touchpanel: ST-1700C · 21 1-Way Wireless RF Touchpanel Crestron ST-1700C Programming with VisionToolsTM Pro-e Control screen variations incorporating two- and three-dimensional graphics and text are possible and can be created with VT Pro-e, a design and programming Windowsbased software program. [. . . ] To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ]