User manual CRESTRON SP-SC

[. . . ] 5729 Slide Controller: SP-SC · 1 CRESTRON Specifications Dimensions: Length Width Height Connector Type Length Connector Type Length 4. 850" (123. 19 mm) 1. 324" (33. 63 mm) 1. 052" (26. 72 mm) 6. 2 oz. (176 g) EBY, Five-pin, Pickle 6' (183 cm) 3. 5 mm, Straight, Stereo 3' (91. 44 cm) Crestron p/n CNSP-112 Input 120V 60Hz 18W Output 12vDC 0. 5A Input 230V 50Hz 110mA Output 12V---1. 0A 12VA Version 1. 20. 04 or later Version 1. 1. 3 or later Version 11. 7. 207 or later Weight: Projector Cable: Serial Data Cable¹: Serial Data Cable²: 12v DC Power Supply*: Crestron p/n PW-1205 (USA and Canada) Crestron p/n PWI-1210 (International) Software: SIMPLTM Windows® VisionTools ProTM Crestron Database ¹ For SmartPresenter and SmarTouch ST-CP (supplied) ² Required for use with CNMSX (Sold separately) * Required for use with SmarTouch ST-CP and CNMSX (sold separately) Cable Length = 6' (183 cm) 4. 850" (123. 19 mm) 1. 324" (33. 63 mm) 1. 052" (26. 72 mm) 2 · Slide Controller: SP-SC Operations Guide - DOC. 5729 CRESTRON Setup SP-SC with SmartPresenterTM Connect the 3. 5 mm, Serial Data Cable (supplied) to the input port on the SP-SC. The EBY, fivepin, pickle type connector should be plugged into the projector. [. . . ] NOTE: An external power supply must be used when using the SP-SC with the CNMSX system. A CNSP-112 Serial Data Cable is also required. Connect to CNMSX Serial Data Cable CNSP-112 External Power Supply To Slide Projector S G Serial Data Cable CNSP-112 Operations Guide - DOC. 5729 Slide Controller: SP-SC · 5 CRESTRON Programming SmartPresenterTM SP-1 The SmartPresenter is field programmable and does not require a PC. Refer to the latest revision of the SmartPresenter ­ Quick Guide (DOC. SmartPresenter software is available, however, it is only necessary for changing drivers, cloning SP-1 machines, and updating firmware. SmarTouchTM ST-CP The SmarTouch systems are easily programmed using the SmarTouch STS Wizard. In several easy steps a SmarTouch system can be programmed and up-loaded. SmarTouch systems may also be custom programmed using Crestron's easy-to-use SIMPLTM Windows® and VisionTools ProTM software. CNMSX The CNMSX is programmed using Crestron's easy-to-use SIMPLTM Windows® software. Example Program shown as Block Diagram This example allows a touchpanel to control a slide projector via the IR-Device (SPSC). Feedback is provided to alert the touchpanel user that a button is, in fact, being pressed. This SP-SC driver can be located in the Crestron Database (version 11. 7. 207 or later), under Slide Controllers. 6 · Slide Controller: SP-SC Operations Guide - DOC. 5729 CRESTRON Problem Solving Troubleshooting TROUBLE SP-SC not functioning. POSSIBLE CAUSE(S) SmartPresenter Q-Code incorrect SmarTouch ST-CP /CMMSX Incorrect Driver Selected No 12v power supply CORRECTIVE ACTION Verify that the correct Q-Code for the device has been assigned. Select the correct driver from the Crestron database. 12v power supply must be used (see "Specifications" on page 2). Further Inquiries If after reviewing this Operations Guide, you cannot locate specific information or have questions, please take advantage of Crestron's award winning technical support team by calling: · · · · · · In the US and Canada, call Crestron's corporate headquarters at 1. 888. CRESTRON [1. 888. 273. 7876] or 1. 201. 767. 3400. In Latin America, call Crestron Latin America at +525. 574. 15. 90. For local support from exclusive Crestron factory trained personnel call: In Australia, call Soundcorp at +613. 941. 61066. In New Zealand, call Amber Technologies at +649. 410. 8382. Operations Guide - DOC. 5729 Slide Controller: SP-SC · 7 CRESTRON Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ] Furthermore, this warranty does not cover any product that has had the serial number altered, defaced, or removed. This warranty shall be the sole and exclusive remedy to the purchaser. In no event shall CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages inclusive) arising from the sale or use of this equipment. CRESTRON makes no other warranties nor authorizes any other party to offer any warranty, expressed or implied, including warranties of merchantability for this product. [. . . ]