User manual CRESTRON SMK-12 SMK-15 SMK-17

[. . . ] 6467 Contents · i Crestron SMK-12/15/17 Swivel Mount Kit Swivel Mount Kit: SMK-12/15/17 Introduction The Swivel Mount Kit, SMK-12/15/17 is designed for the TPS-12/15/17, TPS-G and TPMC-15/17 family of Crestron tilt touchpanels with the required rectangular cutout in the base of the unit as shown in the drawing on page 2. The SMK-12/15/17 is a sturdy mounting option that provides cable management, wire strain relief, and prevents unauthorized users from disconnecting and removing the touchpanel. The opening at the rear of the SMK-12/15/17 is sized to accommodate all of the cables that would typically be connected to the touchpanel, allowing them to be hidden from view by routing them down through the mounting surface through the center opening. The SMK-12/15/17 swivel mount kit reduces the chance of theft while improving viewing convenience. [. . . ] 6467 Swivel Mount Kit: SMK-12/15/17 · 3 Swivel Mount Kit SMK-12/15/17 Swivel Mount Kit Assembly Diagram Route Cables Through This Opening To Touchpanel Ports Crestron SMK-12/15/17 SWIVEL MOUNT PLATE #8-32 X ¼ PAN HEAD SCREW (2007263) QTY 4 TOTAL TO MOUNT THE SWIVEL MOUNT PLATE TO THE BASE OF THE TOUCHPANEL SWIVEL MOUNT ASSEMBLY #8-32 X ¼ PAN HEAD SCREW (2014325) QTY 4 TOTAL BENT TAB FLAT TAB SPRING-LOADED SCREWS MOUNTING SURFACE FRONT SECURITY PLATE (2004824) QTY 1 #8-32 X 1" PAN HEAD SCREW (2007276) OR #8-32 x 5/8" (2007274) QTY 4 TOTAL From Interface Box 8. Route the cables from the interface box up through the Security Plate, through the mounting surface, through the Swivel Mount Assembly, and then through the opening in the base of the touchpanel. Being careful to avoid damage to the cables, attach the Swivel Mount Assembly to the Swivel Mount Plate, using the supplied four #8-32 X ¼" screws through the holes in the Swivel Mount Assembly into the standoff posts on the Swivel Mount Plate. Make certain the cables are not twisted or crimped and have sufficient slack at the port connections before fully tightening the screws. 9. 10. Making certain that the tabs (one bent and one flat) are positioned to the front and rear of the Swivel Mount Assembly, place the touchpanel and Swivel Mount Assembly down on the mounting surface. Guide the standoff posts on the Swivel Mount Assembly through the holes you drilled in the mounting surface. 4 · Swivel Mount Kit: SMK-12/15/17 Installation Guide ­ DOC. Hold the Security Plate in position under the mounting surface and secure the entire assembly using the #8-32 x 5/8" screws for surfaces 3/4 to 1 1/8inches (19 to 28. 6 mm) thick; or the #8-32 x 1" screws for surfaces 1 1/8 to 1 3/8 inches (28. 6 to 35 mm) thick. Adjust the tension of the Swivel Mount Assembly using the four springloaded screws on the underside. Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. For assistance in your local time zone, refer to the Crestron website (www. crestron. com) for a listing of Crestron worldwide offices. You can also log onto the online section of the Crestron website to ask questions about Crestron products. First-time users will need to establish a user account to fully benefit from all available features. As of the date of manufacture, the SMK-12/15/17 has been tested and found to comply with specifications for CE marking. Future Updates As Crestron adds improvements to the SMK-12/15/17, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Check the Crestron website periodically for manual update availability and its relevance. Updates are identified as an "Addendum" in the Download column. Installation Guide ­ DOC. 6467 Swivel Mount Kit: SMK-12/15/17 · 5 Swivel Mount Kit Crestron SMK-12/15/17 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ] CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. [. . . ]