User manual CRESTRON SER-3500

[. . . ] CRESTRON Contents Series 3500 Touchpanels 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Physical Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Configuration Differences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 8108B Series 3500 Touchpanels · 9 CRESTRON VT-3500 Typical Connection Diagram NOTE: UNITS IN THIS ILLUSTRATION ARE NOT DRAWN TO SCALE. CABLE ASSEMBLY (P/N 15709) CONNECT TO VIDEO SOURCE CONNECT TO CNMS, CNRACK, OR CNRACK-D SIDE VIEW OF VT-3500 Refer to the CRESNET II Network Cable drawing in this section of the Guide. · Connect the CT-3500L or VT-3500L directly to the CRESNET II system via the network cable, shown below. CT/VT-3500L Typical Connection Diagram NOTE Connections shown also apply to the CT-3500L, except where specified. CONNECT TO ANY VGA DEVICE (i. e. , VIDEO PROJECTOR) CONNECT TO CNMS, CNRACK, OR CNRACK-D Refer to the CRESNET II Network Cable drawing in this section of the Guide. CONNECT TO SERIAL PORT OF COMPUTER Use only for direct connection to PC to load panels without network. CONNECT TO VIDEO SOURCE Applies only to VT-3500L. NOTE: Network termination points are available at the control system power supply. Refer to the latest revision of the CRESNET II reference manual section on CNPWS power supplies (Doc. If composite video is required, connect video cable to VIDEO COMP port (composite video input). Otherwise, if S-video is required, connect chrominance and luminance to VIDEO C and VIDEO Y ports, respectively. Select appropriate input in the Setup Menu as described in the Configuring the Touchpanel section. If necessary, connect a VGA device, such a a video projector, to VGA OUTPUT. Apply power to the touchpanel and observe illumination of the touchsensitive screen. The touchpanel enters RUN MODE and displays a 4. 5. 10 · Series 3500 Touchpanels Operations Guide - DOC. To enter SETUP MODE and not RUN MODE, hold a finger to the touchscreen as power is applied. The user may configure the unit while in SETUP MODE. Configuring the Touchpanel To configure the unit, it may be necessary to access a series of setup screens prior to viewing run-time screens that are loaded into the touchpanel for normal operation. The Main Menu for configuring the touchpanel appears when a finger is held to the touchscreen as power is applied. Remove your finger when the message "SETUP MODE" appears on the touchscreen. Holding a finger to the touchscreen for five seconds after the "SETUP MODE" message is displayed sets the brightness to high. Upon entering SETUP MODE, the Main Screen, shown below, displays four buttons: TOUCH SCREEN CALIBRATION, DIAGNOSTICS, SETUP, and SAVE SETUP AND RUN PROGRAM. Main Menu Calibration Menu Calibration of the touchscreen is required if the active touch area of a button does not coincide with the button's image. Select the TOUCH SCREEN CALIBRATION button to display the Calibration Menu, shown below. The Calibration Menu offers the choice to initiate calibration with the Perform Calibration button or return to the previous screen with the Return to Main Menu button. If you proceed to calibrate the touchpanel, the screen prompts you with the message "Touch Screen Calibration Menu" nearly centered on the display. Another message, "Touch Upper Left Corner", appears in the upper left corner. Another message, "Touch Lower Right Corner", appears in the lower right corner. Touch the corner of the screen to return to the Main Menu. Calibration Menu Operations Guide - DOC. 8108B Series 3500 Touchpanels · 11 CRESTRON Diagnostics Menu The DIAGNOSTICS button from the Main Menu should only be used under supervision from a CRESTRON technical support representative during telephone support. The options available from the Diagnostics Menu, shown below, are numeric in nature and their interpretation is beyond the scope of this manual. Diagnostics Menu (ColorTouch [left] & VideoTouch [right] Configurations) Setup Menu To obtain the Setup Menu, shown below, select and hold the SETUP button from the Main Menu until the Setup Menu is displayed. [. . . ] It is a sample of SIMPL-C programming for the block diagram example illustrated in "Programming" on page 15. NET. ID <03 to FE>: CTP-3000 i1 o1 " i4 o4 = <relay1> = <relay1_fb> =" " = <relay4> =<relay4_fb> \i1 refers to join# of touchpanel button 20 · Series 3500 Touchpanels Operations Guide - DOC. 8108B CRESTRON Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. [. . . ]