User manual CRESTRON SER-3200

[. . . ] CRESTRON Contents Series 3200 Touchpanels 1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Physical Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Configuration Differences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] In local mode, the directory buttons change pages, but buttons requiring feedback do not work. Two centrally located buttons on the Interface Menu, LOCAL and CRESNET II, determine communication mode. Select Local to set the touchpanel into demo mode and CRESNET II for normal Cresnet communication mode. Text within the selected button changes color from black to light gray. Communication mode is factory set to CRESNET II. Operations Guide - DOC. 5725 Series 3200 Touchpanels · 13 CRESTRON Two side-by-side buttons, RS-232 ON and RS-232 OFF, are located just above the RETURN button at the bottom of the Interface Menu. If the touchpanel is utilized in a system without a Cresnet system, ensure that the RS-232 ON button is selected. Additional RS-232 parameters must be set with the RS-232 Menu since alternative parameters may be required for successful transfers to a PC. Text within the selected button changes color from black to light gray. Select the RETURN button, located at the bottom of the Interface Menu, after interface parameters have been set. RS-232 Menu (Lectern-Mount Configurations Only) Select the RS-232 button, located at the top of the second column of the Setup Menu, to change the touchpanel display to the RS-232 Menu, shown below. The RS-232 Menu specifies four parameters required for the touchpanel to use its RS-232 serial port. Ten baud rate buttons, labeled 110, 150, 300, 600, 1200, 2400, 4800, 9600, 19200, and 38400, are available for selection. Also select seven or eight data bits; none, odd, or even parity; one or two stop bits. RS-232 Menu RTS/CTS handshaking is supported by the Series 3200 touchpanels. Selections for all RS-232 parameters are indicated with light gray text. The parameters are factory set to 38. 4 Kbd, eight data bits, no parity bits, and one stop bit. If necessary, refer to "Appendix: RS-232 Protocol" on page 21. Select the Save and Return button, located at the bottom of the RS-232 Menu, after RS-232 parameters have been set. Sound Menu The SOUND button, located at the top right corner of the Setup Menu, is used to display the Sound Menu, shown on the next page. Confirmation of a button press on a touchpanel is acknowledged by an audible click assuming this feature is enabled. To enable this feature, verify that the KEYCLICK ON button is active (light gray text). Volume of the audible click is controlled with the VOLUME UP and VOLUME DOWN buttons. The unit is factory set with the sound on. 14 · Series 3200 Touchpanels Operations Guide - DOC. 5725 CRESTRON Sound Menu Save Setup and Run Program The Save Setup and Run Program button, located at the upper right corner of the Main Menu, saves all of the setup information to EEPROM and displays the main page that has been programmed into your system. Programming with SIMPLTM Windows NOTE: VisionTools Pro (VT Pro) is a Windows compatible software package for creating Crestron touchpanel screen designs. [. . . ] To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ]