User manual CRESTRON MMK-4L WMKM-4L

[. . . ] The WMKM-4L consists of five parts­three of which make up the MMK-4L­as well as one mounting plate and one cutout template. The mounting plate provides the necessary support for post-construction applications. Installation Guide ­ DOC. 6389 Mud Mount Kits: MMK-4L & WMKM-4L · 1 Mud Mount Kits Crestron MMK-4L & WMKM-4L Supplied Hardware of the MMK-4L and WMKM-4L DESCRIPTION Metal Plate, Mounting (WMKM-4L only) Metal Plate, Mud Ring Metal Plate, Adjustment Overlay Template, Cutout (WMKM-4L only) Hardware, Push-On Fastener Dimensional Drawings PART NUMBER 2013242 2013240 2013243 4007975 2004121 QUANTITY 1 1 2 1 4 MOUNTING PLATE FOR WMKM-4L 6. 75 in (17. 15 cm) 0. 06 in (0. 15 cm) ADJUSTMENT PLATE FOR MMK-4L AND WMKM-4L 0. 38 in (0. 97 cm) 5. 55 in (14. 10 cm) 6. 67 in (16. 94 cm) 0. 37 in (0. 94 cm) MUD RING PLATE FOR MMK-4L AND WMKM-4L 7. 06 in (17. 93 cm) 0. 02 in (0. 05 cm) 5. 09 in (12. 93 cm) 2. 26 in (5. 74 cm) 2 · Mud Mount Kits: MMK-4L & WMKM-4L Installation Guide ­ DOC. 6389 Crestron MMK-4L & WMKM-4L Mud Mount Kits Drywall Cutout Templates and Dimensions (supplied with WMKM-4L only) 6. 75 in (17. 15 cm) 0. 76 in (1. 93 cm) 0. 21 in (0. 53 cm) 5. 55 in (14. 10 cm) 4. 04 in (10. 26 cm ) 3. 83 in (9. 73 cm) 0. 56 in (1. 42 cm) 1. 30 in (3. 30 cm) 4. 32 in (10. 97 cm) 5. 63 in (14. 30 cm) 5. 63 in (14. 30 cm) 0. 21 in (0. 53 cm) 4. 04 in (10. 26 cm) 3. 63 in (9. 22 cm) 1. 30 in (3. 30 cm) 3. 02 in (7. 67 cm) Installation This section provides an installation procedure for each Mud Mount Kit. [. . . ] The screws pass through the clearance holes in the PMK-4L (or BB-4L) and are secured in the extruded holes of the adjustment plates. Verify that the mud ring plate is level. 7. NOTE: Do not over tighten screws. Use a #2 Phillips screwdriver and tighten the drywall screws by hand so that they slightly dimple into the holes in the mud ring plate. Run the necessary cables for the touchpanel and secure them behind the drywall. When dry, the touchpanel can be installed using the four tapped holes in the PMK-4L. 6389 Mud Mount Kits: MMK-4L & WMKM-4L · 5 Mud Mount Kits WMKM-4L Procedure Crestron MMK-4L & WMKM-4L The procedure in this section provides the necessary steps for the assembly and installation of the WMKM-4L into a wall. The only tools or materials required and not supplied are a drywall saw or equivalent, a level, four standard drywall screws, #2 Phillips screwdriver, and tools/material to apply drywall joint compound. CAUTION: Allow an air gap of at least 12 inches in the wall cavity above the touchpanel for heat dissipation. Insert the two pins on one adjustment plate into the top two outer holes on the mounting plate, as shown in the following illustration. Create the Adjustment/Mounting Plate Assembly (4) PUSH-ON FASTENER (2004121) (1) MOUNTING PLATE (2013242) (2) ADJUSTMENT PLATE (2013243) 2. Slide a push-on fastener over each pin on the adjustment plate to loosely secure the adjustment plate and the mounting plate. Slide them on enough to keep the adjustment plate and mounting plate as one adjustment/mounting plate assembly. Use the second adjustment plate and repeat steps 1 and 2 using the lower two pins. Locate an area on the wall that is free of miscellaneous wiring and studs. Make a small hole near the middle of the designated site; verify that the location is suitable. 3. Use the drywall saw or equivalent to produce a level, rectangular cutout in the drywall as shown on page 3. Insert the symmetrical mud ring plate into the opening, as shown in the illustration after this step. 6 · Mud Mount Kits: MMK-4L & WMKM-4L Installation Guide ­ DOC. 6389 Crestron MMK-4L & WMKM-4L Insert the Mud Ring Plate into the Opening DRYWALL Mud Mount Kits FLANGE HOLES FOR DRYWALL SCREWS (NOT INCLUDED). SCREW LENGTH SHOULD NOT EXCEED DRYWALL THICKNESS BY MORE THAN ½ INCH. MUD RING PLATE (2013240) 8. Carefully pass the adjustment/mounting plate assembly through the opening and rest the assembly against the interior surface of the drywall. Verify that the adjustment plates are between the mounting plate and the drywall. When the adjustment/mounting plate assembly is in position, bend the top two flanges of the mud ring upward (approximately 90 degrees) and the bottom two flanges downward (approximately 90 degrees). Refer to the illustration after this step. 9. NOTE: Adjustment/mounting plate assembly will have slight play; this is normal. It allows for minor adjustments to the touchpanel during installation. Bend Flanges 10. Use four standard drywall screws (of adequate length) to secure the plate to the adjustment/mounting plate assembly. [. . . ] CRESTRON is not liable for any claim made by a third party or made by the purchaser for a third party. CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. [. . . ]