User manual CRESTRON MMK-4000L WMKM-4000L

[. . . ] The mounting plate is the part that provides the necessary support for post-construction applications. Supplied Hardware of the MMK-4000L and WMKM-4000L DESCRIPTION Metal Plate, Mounting (WMKM-4000L only) Metal Plate, Mud Ring Metal Plate, Fastener Hardware, Push-On Fastener PART NUMBER 2011515 2011517 2004825 2004121 QUANTITY 1 1 2 4 Installation Guide ­ DOC. 6303 Mud Mount Kits: MMK-4000L & WMKM-4000L · 1 Mud Mount Kits Crestron MMK-4000L & WMKM-4000L The dimensions of the MMK-4000L/WMKM-4000L are shown below. Dimensional Drawing 0. 38 in (0. 95 cm) 8. 99 in (22. 84 cm) 5. 91 in (15. 01 cm) 12. 63 in (32. 08 cm) 0. 06 in (0. 15 cm) 0. 38 in (0. 95 cm) MOUNTING PLATE FOR WMKM-4000L FASTENER PLATE FOR WMKM-4000L AND MMK-4000L 9. 34 in (23. 73 cm) 12. 79 in (32. 49 cm) 0. 05 in (0. 13 cm) 2. 26 in (5. 73 cm) MUD RING PLATE FOR WMKM-4000L AND MMK-4000L Drywall Cutout Dimensions 7 3132 in (202 mm) 819 64 in MAX (211 mm MAX) DO NOT EXCEED THIS DIMENSION 118 in 1113 32 in MAX (28 mm) (290 mm MAX) DO NOT EXCEED THIS DIMENSION 2 · Mud Mount Kits: MMK-4000L & WMKM-4000L Installation Guide ­ DOC. 6303 Crestron MMK-4000L & WMKM-4000L Mud Mount Kits Installation This section provides an installation procedure for each Mud Mount Kit. The procedure for the MMK-4000L starts below and the "WMKM-4000L Procedure" starts on page 5. MMK-4000L Procedure The procedure in this section provides the necessary steps for the assembly of the MMK-4000L to either the PMK-4000L or BB-4000L. [. . . ] The screws pass through the clearance holes in the PMK-4000L (or BB-4000L) and are secured in the extruded holes of the fastener plates. Verify that the mud ring plate is level. 8. NOTE: Do not over tighten screws. Use a #2 Phillips screwdriver and tighten the drywall screws by hand so that they slightly dimple into the holes in the mud ring plate. 10. Run the necessary cables for the touchpanel and secure them behind the drywall. When dry, the TPS-4000L can be installed using the four tapped holes in the PMK-4000L. 6301) for details. WMKM-4000L Procedure The procedure in this section provides the necessary steps for the assembly and installation of the WMKM-4000L into a wall. The only tools or materials required and not supplied are a drywall saw or equivalent, a level, four standard drywall screws, #2 Phillips screwdriver, and tools/material to apply drywall joint compound. Insert the two pins on one fastener plate into the top two outer holes on the mounting plate, as shown in the following illustration. (4) PUSH-ON FASTENER (2004121) Create the Fastener/Mounting Plate Assembly (1) MOUNTING PLATE (2011515) (2) FASTENER PLATE (2004825) Installation Guide ­ DOC. 6303 Mud Mount Kits: MMK-4000L & WMKM-4000L · 5 Mud Mount Kits 2. Crestron MMK-4000L & WMKM-4000L Slide a push-on fastener over each pin on the fastener plate to loosely secure the fastener plate and the mounting plate. Slide them on enough to keep the fastener plate and mounting plate as one fastener/mounting plate assembly. Use the second fastener plate and repeat steps 1 and 2 using the lower two PMK-4000L pins. Locate an area on the wall that is free of miscellaneous wiring and studs. Make a small hole near the middle of the designated site; verify that the location is suitable. 3. Use the drywall saw or equivalent to produce a level, rectangular cutout in the drywall as shown on page 2. Insert the symmetrical mud ring plate into the opening, as shown in the illustration after this step. Insert the Mud Ring Plate into the Opening IMPORTANT: PLEASE MAKE DRYWALL CUTOUT AS LEVEL AND CLEAN AS POSSIBLE. THE MOUNTING PLATE ALLOWS FOR ONLY MINOR ADJUSTMENT OF THE TPS-4000L. FLANGE MUD RING PLATE (2011517) HOLES FOR DRYWALL SCREWS (PROVIDED BY OTHER), SCREW LENGTH SHOULD NOT EXCEED DRYWALL THICKNESS BY MORE THAN 1/2"). 8. Carefully pass the fastener/mounting plate assembly through the opening and rest the assembly against the interior surface of the drywall. Verify that the fastener plates are between the mounting plate and the drywall. 6 · Mud Mount Kits: MMK-4000L & WMKM-4000L Installation Guide ­ DOC. 6303 Crestron MMK-4000L & WMKM-4000L 9. Mud Mount Kits When the fastener/mounting plate assembly is in position, bend the top two flanges of the mud ring upward (approximately 90 degrees) and the bottom two flanges downward (approximately 90 degrees). Refer to the illustration after this step. NOTE: Fastener/mounting plate assembly will have slight play; this is normal. It allows for minor adjustments to the TPS-4000L during installation. Bend Flanges 10. Use four standard drywall screws (of adequate length) to secure the plate to the fastener/mounting plate assembly. The screws pass through the clearance holes in the plate and are secured in the extruded holes of the fastener plates. [. . . ] CRESTRON is not liable for any claim made by a third party or made by the purchaser for a third party. CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. [. . . ]