User manual CRESTRON MMK-3000L WMKM-3000L

[. . . ] The mounting plate is the part that provides the necessary support for post-construction applications. Supplied Hardware of the MMK-3000L and WMKM-3000L DESCRIPTION Metal Plate, Mounting (WMKM-3000L only) Metal Plate, Mud Ring Metal Plate, Fastener Hardware, Push-On Fastener PART NUMBER MTPL02848-1 MTPL02850-1 MTPL02874-1 MMHO-11 QUANTITY 1 1 2 4 Installation Guide ­ DOC. 6021 Mud Mount Kits: MMK-3000L & WMKM-3000L · 1 Mud Mount Kits Crestron MMK-3000L & WMKM-3000L The dimensions of the MMK-3000L/WMKM-3000L are shown below. Dimensional Drawing 0. 70 in (1. 78 cm) 0. 38 in (0. 95 cm) 5. 90 in (14. 99 cm) 0. 61 in (1. 54 cm) 7. 84 in (19. 91 cm) 10. 06 in (25. 55 cm) MOUNTING PLATE FOR WMKM-3000L 0. 38 in (0. 95 cm) 0. 06 in (0. 15 cm) 0. 05 in (0. 12 cm) FASTENER PLATE FOR WMKM-3000L AND MMK-3000L 8. 13 in (20. 65 cm) 10. 16 in (25. 81 cm) MUD RING PLATE FOR WMKM-3000L & MMK-3000L 0. 07 in (0. 18 cm) 2. 26 in (5. 73 cm) Drywall Cutout Dimensions 2 · Mud Mount Kits: MMK-3000L & WMKM-3000L Installation Guide ­ DOC. 6021 Crestron MMK-3000L & WMKM-3000L Mud Mount Kits Installation This section provides an installation procedure for each Mud Mount Kit. The procedure for the MMK-3000L starts below and the "WMKM-3000L Procedure" starts on page 5. MMK-3000L Procedure The procedure in this section provides the necessary steps for the assembly of the MMK-3000L to either the PMK-3000L or BB-3000L. [. . . ] 6021 Crestron MMK-3000L & WMKM-3000L 7. Mud Mount Kits Use four standard drywall screws (length should not exceed drywall thickness by more than ½ inch) to secure the mud ring plate to the rest of the assembly. The screws pass through the clearance holes in the PMK-3000L (or BB-3000L) and are secured in the extruded holes of the fastener plates. Verify that the mud ring plate is level. 8. NOTE: Do not over tighten screws. Use a #2 Phillips screwdriver and tighten the drywall screws by hand so that they slightly dimple into the holes in the mud ring plate. 10. Run the necessary cables for the touchpanel and secure them behind the drywall. When dry, the TPS-3000L can be installed using the four tapped holes in the PMK-3000L. 6077) for details. WMKM-3000L Procedure The procedure in this section provides the necessary steps for the assembly and installation of the WMKM-3000L into a wall. The only tools or materials required and not supplied are a drywall saw or equivalent, a level, four standard drywall screws, #2 Phillips screwdriver, and tools/material to apply drywall joint compound. Insert the two pins on one fastener plate into the top two outer holes on the mounting plate, as shown in the illustration after this step. (4) PUSH-ON FASTENER Create the Fastener/Mounting Plate Assembly MOUNTING PLATE FASTENER PLATE Installation Guide ­ DOC. 6021 Mud Mount Kits: MMK-3000L & WMKM-3000L · 5 Mud Mount Kits 2. Crestron MMK-3000L & WMKM-3000L Slide a push-on fastener over each pin on the fastener plate to loosely secure the fastener plate and the mounting plate. Slide them on enough to keep the fastener plate and mounting plate as one fastener/mounting plate assembly. Use the second fastener plate and repeat steps 1 and 2 using the lower two PMK-3000L pins. Locate an area on the wall that is free of miscellaneous wiring and studs. Make a small hole near the middle of the designated site; verify that the location is suitable. 3. Use the drywall saw or equivalent to produce a level, rectangular cutout in the drywall as shown on page 2. Insert the symmetrical mud ring plate into the opening, as shown in the illustration after this step. Insert the Mud Ring Plate into the Opening 8. Carefully pass the fastener/mounting plate assembly through the opening and rest the assembly against the interior surface of the drywall. Verify that the fastener plates are between the mounting plate and the drywall. 6 · Mud Mount Kits: MMK-3000L & WMKM-3000L Installation Guide ­ DOC. 6021 Crestron MMK-3000L & WMKM-3000L 9. Mud Mount Kits When the fastener/mounting plate assembly is in position, bend the top two flanges of the mud ring upward (approximately 90 degrees) and the bottom two flanges downward (approximately 90 degrees). Refer to the illustration after this step. NOTE: Fastener/mounting plate assembly will have slight play; this is normal. It allows for minor adjustments to the TPS-3000L during installation. Bend Flanges 10. Use four standard drywall screws (of adequate length) to secure the plate to the fastener/mounting plate assembly. The screws pass through the clearance holes in the plate and are secured in the extruded holes of the fastener plates. [. . . ] Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. [. . . ]