User manual CRESTRON MMK-2000L WMKM-2000L

[. . . ] The mounting plate is the item that provides the necessary support for post-construction applications. Supplied Hardware of the MMK-2000L and WMKM-2000L · ONE · ONE · TWO (1) (1) (2) Metal Plate, Mounting (only on WMKM-2000L) Metal Plate, Mud Ring Metal Plate, Fastener Metal, Push-on Fastener · FOUR (4) Installation Guide ­ DOC. 6025 Mud Mount Kits: MMK-2000L & WMKM-2000L · 1 Mud Mount Kits Crestron MMK-2000L & WMKM-2000L Installation This section provides an installation procedure for each Mud Mount Kit. The procedure for the MMK-2000L starts below and the "WMKM-2000L Procedure" starts on page 4. MMK-2000L Procedure The procedure in this section provides the necessary steps for the assembly of the MMK-2000L to either the PMK-2000L or BB-2000L. It is assumed that the PMK-2000L or BB-2000L has been secured to the stud according to the procedures in the latest revisions of their respective Installation Guides (Doc. [. . . ] Verify that the mud ring plate is level. 7. 8. Installation Guide ­ DOC. 6025 Mud Mount Kits: MMK-2000L & WMKM-2000L · 3 Mud Mount Kits Crestron MMK-2000L & WMKM-2000L NOTE: Do not over tighten screws. Use a #2 Phillips screwdriver and tighten the drywall screws by hand so that they slightly dimple into the holes in the mud ring plate. 10. When dry, the TPS-2000L can be installed using the four tapped holes in the PMK-2000L. 5972) for details. WMKM-2000L Procedure The procedure in this section provides the necessary steps for the assembly and installation of the WMKM-2000L into a wall. The only tools or materials required and not supplied are a drywall saw or equivalent, a level, four standard drywall screws, #2 Phillips screwdriver, and tools/material to apply drywall joint compound. Insert the two pins on one fastener plate into the top two outer holes on the mounting plate, as shown in the illustration after this step. Create the Fastener/Mounting Plate Assembly MOUNTING PLATE QUANTITY 1 PUSH-ON FASTENER QUANTITY 4 FASTENER PLATE QUANTITY 2 2. Slid two push-on fasteners over the pins on the fastener plate to loosely secure the fastener plate and the mounting plate. Slid them on enough to keep the fastener plate and mounting plate as one fastener/mounting plate assembly. Use the second fastener plate and repeat steps 1 and 2 on the opposite side of the mounting plate. 3. 4 · Mud Mount Kits: MMK-2000L & WMKM-2000L Installation Guide ­ DOC. 5. Mud Mount Kits Locate an area on the wall that is free of miscellaneous wiring and studs. Make a small hole near the middle of the designated site; verify that the location is suitable. NOTE: Make the cutout as level as possible. Use the drywall saw or equivalent to produce a level, rectangular cutout in the drywall that measures 6 3/8 inches wide (16. 159 cm) x 4 ½ inches high (11. 389 cm). Insert the symmetrical mud ring plate into the opening, as shown in the illustration after this step. 7. Insert the Mud Ring Plate into the Opening MUD RING PLATE QUANTITY 1 8. OPENING IN DRYWALL Carefully pass the fastener/mounting plate assembly through the opening and rest the assembly against the interior surface of the drywall. Verify that the fastener plates are between the mounting plate and the drywall. Refer to the illustration after this step for visual guidance. Installation Guide ­ DOC. 6025 Mud Mount Kits: MMK-2000L & WMKM-2000L · 5 Mud Mount Kits Crestron MMK-2000L & WMKM-2000L Fastener Plates Located Between Mounting Plate and Drywall FASTENER/ MOUNTING PLATE ASSEMBLY INSERTED MUD RING PLATE 9. When the fastener/mounting plate assembly is in position, bend the top two flanges of the mud ring upward (approximately 90 degrees) and the bottom two flanges downward (approximately 90 degrees). Refer to the illustration after this step. NOTE: Fastener/mounting plate assembly will have slight play; this is normal. It allows for minor adjustments to the TPS-2000L during installation. Bend Flanges BEND FLANGES UP APPROXIMATELY 90° BEND FLANGES DOWN APPROXIMATELY 90° 6 · Mud Mount Kits: MMK-2000L & WMKM-2000L Installation Guide ­ DOC. Use four standard drywall screws (of adequate length) to secure the plate to the fastener/mounting plate assembly. The screws pass through the clearance holes in the plate and are secured in the extruded holes of the fastener plates. Secure Mud Ring Plate STANDARD DRYWALL SCREW (NOT SUPPLIED) QUANTITY 4 11. Use a #2 Phillips screwdriver and tighten the drywall screws by hand so that they slightly dimple into the holes in the mud ring plate. [. . . ] Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. [. . . ]