User manual CRESTRON MMK-15L WMKM-15L

[. . . ] These parts produce an assembly that attaches to the PMK-15L or BB-15L. The WMKM-15L consists of the same three parts that make up the MMK-15L as well as one mounting plate. The mounting plate is the part that provides the necessary support for post-construction applications. Installation Guide ­ DOC. 6364 Mud Mount Kits: MMK-15L & WMKM-15L · 1 Mud Mount Kits Crestron MMK-15L & WMKM-15L Supplied Hardware of the MMK-15L and WMKM-15L DESCRIPTION Metal Plate, Mounting (WMKM-15L only) Metal Plate, Mud Ring Metal Plate, Fastener Hardware, Push-On Fastener Dimensional Drawings PART NUMBER 2012920 2013005 2004825 2004121 QUANTITY 1 1 2 4 13. 79 in (35. 02 cm) 5. 90 in (14. 99 cm) 14. 13 in (35. 88 cm) 14. 19 in (36. 05 cm) MOUNTING PLATE FOR WMKM-15L 0. 06 in (0. 15 cm) 0. 38 in (0. 95 cm) 0. 38 in (0. 95 cm) 14. 80 in (37. 59 cm) MUD RING PLATE FOR WMKM-15L & MMK-15L 2. 26 in (5. 73 cm) FASTENER PLATE FOR WMKM-15L & MMK-15L NOTE: The inside edge of the mounting plate can be used as a cutout template. Drywall Cutout Dimensions ~137 64 in (333 mm Max) DO NOT EXCEED THIS DIMENSION ~126164 in (329 mm Max) ~123 4 in (324 mm Max) ~15 64 in (28 mm Max) TYP (4X) ~32132 in (93 mm Max) ~613 64 in (158 mm Max) ~1312 in (343 mm Max) DO NOT EXCEED THIS DIMENSION ~5 64 in (2 mm Max) Ø ~3 16 in (5 mm Max) TYP (4X) ~3 16 in (5 mm Max) 2 · Mud Mount Kits: MMK-15L & WMKM-15L Installation Guide ­ DOC. [. . . ] Use a #2 Phillips screwdriver and tighten the drywall screws by hand so that they slightly dimple into the holes in the mud ring plate. 10. Avoid covering the four tapped mounting holes. 4 · Mud Mount Kits: MMK-15L & WMKM-15L Installation Guide ­ DOC. Run the necessary cables for the touchpanel and secure them behind the drywall. When dry, the touchpanel can be installed using the four tapped holes in the PMK-15L. Refer to the latest revision of the TPS-12L/15L/17L Operations Guide (Doc. 6354) for installation instructions. WMKM-15L Procedure The procedure in this section provides the necessary steps for the assembly and installation of the WMKM-15L into a wall. The only tools or materials required and not supplied are a drywall saw or equivalent, a level, four standard drywall screws, #2 Phillips screwdriver, and tools/material to apply drywall joint compound. CAUTION: Allow an air gap of at least 12 inches in the wall cavity above the touchpanel for heat dissipation. Insert the two pins on one fastener plate into the top two outer holes on the mounting plate, as shown in the following illustration. Create the Fastener/Mounting Plate Assembly (1) MOUNTING PLATE (2012920) (4)PUSH-ON FASTENER (2004121) (2) FASTENER PLATE (2004825) 2. Slide a push-on fastener over each pin on the fastener plate to loosely secure the fastener plate and the mounting plate. Slide them on enough to keep the fastener plate and mounting plate as one fastener/mounting plate assembly. Use the second fastener plate and repeat steps 1 and 2 using the lower two PMK-15L pins. Locate an area on the wall that is free of miscellaneous wiring and studs. Make a small hole near the middle of the designated site; verify that the location is suitable. 3. The mounting plate allows for only minor leveling adjustments. Installation Guide ­ DOC. 6364 Mud Mount Kits: MMK-15L & WMKM-15L · 5 Mud Mount Kits 6. 7. Crestron MMK-15L & WMKM-15L Use the drywall saw or equivalent to produce a level, rectangular cutout in the drywall as shown on page 2. Insert the symmetrical mud ring plate into the opening, as shown in the illustration after this step. Insert the Mud Ring Plate into the Opening IMPORTANT PLEASE MAKE DRYWALL CUTOUT AS LEVEL AND CLEAN AS POSSIBLE. THE MOUNTING PLATE ALLOWS FOR ONLY MINOR ADJUSTMENT OF THE TOUCHPANEL. FLANGE HOLES FOR DRYWALL SCREWS (PROVIDED BY OTHER) SCREW LENGTH SHOULD NOT EXCEED DRYWALL THICKNESS BY MORE THAN 1/2". MUD RING PLATE (2013005) 8. Carefully pass the fastener/mounting plate assembly through the opening and rest the assembly against the interior surface of the drywall. Verify that the fastener plates are between the mounting plate and the drywall. When the fastener/mounting plate assembly is in position, bend the top two flanges of the mud ring upward (approximately 90 degrees) and the bottom two flanges downward (approximately 90 degrees). Refer to the illustration after this step. 9. NOTE: Fastener/mounting plate assembly will have slight play; this is normal. It allows for minor adjustments to the touchpanel during installation. Bend Flanges 6 · Mud Mount Kits: MMK-15L & WMKM-15L Installation Guide ­ DOC. [. . . ] CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. [. . . ]