User manual CRESTRON MMK-12L WMKM-12L

[. . . ] These parts produce an assembly that attaches to the PMK-12L or BB-12L. The WMKM-12L consists of the same three parts that make up the MMK-12L as well as one mounting plate. The mounting plate is the part that provides the necessary support for post-construction applications. Installation Guide ­ DOC. 6359 Mud Mount Kits: MMK-12L & WMKM-12L · 1 Mud Mount Kits Crestron MMK-12L & WMKM-12L Supplied Hardware of the MMK-12L and WMKM-12L DESCRIPTION Metal Plate, Mounting (WMKM-12L only) Metal Plate, Mud Ring Metal Plate, Fastener Hardware, Push-On Fastener Dimensional Drawings PART NUMBER 2012963 2013002 2004825 2004121 QUANTITY 1 1 2 4 NOTE: You can use the mounting plate as a cutout template. Drywall Cutout Dimensions 2 · Mud Mount Kits: MMK-12L & WMKM-12L Installation Guide ­ DOC. [. . . ] Use a #2 Phillips screwdriver and tighten the drywall screws by hand so that they slightly dimple into the holes in the mud ring plate. 4 · Mud Mount Kits: MMK-12L & WMKM-12L Installation Guide ­ DOC. Run the necessary cables for the touchpanel and secure them behind the drywall. When dry, the touchpanel can be installed using the four tapped holes in the PMK-12L. Refer to the latest revision of the TPS-12L/15L/17L Operations Guide (Doc. 6356) for installation instructions. WMKM-12L Procedure The procedure in this section provides the necessary steps for the assembly and installation of the WMKM-12L into a wall. The only tools or materials required and not supplied are a drywall saw or equivalent, a level, four standard drywall screws, #2 Phillips screwdriver, and tools/material to apply drywall joint compound. CAUTION: Allow an air gap of at least 12 inches in the wall cavity above the touchpanel for heat dissipation. Insert the two pins on one fastener plate into the top two outer holes on the mounting plate, as shown in the following illustration. Create the Fastener/Mounting Plate Assembly 2. Slide a push-on fastener over each pin on the fastener plate to loosely secure the fastener plate and the mounting plate. Slide them on enough to keep the fastener plate and mounting plate as one fastener/mounting plate assembly. Use the second fastener plate and repeat steps 1 and 2 using the lower two PMK-12L pins. Locate an area on the wall that is free of miscellaneous wiring and studs. Make a small hole near the middle of the designated site; verify that the location is suitable. 3. The mounting plate allows for only minor leveling adjustments. Installation Guide ­ DOC. 6359 Mud Mount Kits: MMK-12L & WMKM-12L · 5 Mud Mount Kits 6. 7. Crestron MMK-12L & WMKM-12L Use the drywall saw or equivalent to produce a level, rectangular cutout in the drywall as shown on page 2. Insert the symmetrical mud ring plate into the opening, as shown in the illustration after this step. Insert the Mud Ring Plate into the Opening 8. Carefully pass the fastener/mounting plate assembly through the opening and rest the assembly against the interior surface of the drywall. Verify that the fastener plates are between the mounting plate and the drywall. When the fastener/mounting plate assembly is in position, bend the top two flanges of the mud ring upward (approximately 90 degrees) and the bottom two flanges downward (approximately 90 degrees). Refer to the illustration after this step. 9. NOTE: Fastener/mounting plate assembly will have slight play; this is normal. It allows for minor adjustments to the touchpanel during installation. Bend Flanges 10. Use four standard drywall screws (of adequate length) to secure the plate to the fastener/mounting plate assembly. The screws pass through 6 · Mud Mount Kits: MMK-12L & WMKM-12L Installation Guide ­ DOC. [. . . ] Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. [. . . ]