User manual CRESTRON MMK-1000L WMKM-1000L

[. . . ] The mounting plate is the part that provides the necessary support for post-construction applications. Supplied Hardware of the MMK-1000L and WMKM-1000L DESCRIPTION Metal Plate, Mounting (WMKM-1000L only) Metal Plate, Mud Ring Metal Plate, Fastener Hardware, Push-On Fastener PART NUMBER MTPL02832-1 MTPL02835-1 MTPL02833-1 MMHO-11 QUANTITY 1 1 2 4 Installation Guide ­ DOC. 6062 Mud Mount Kits: MMK-1000L & WMKM-1000L · 1 Mud Mount Kits Crestron MMK-1000L & WMKM-1000L Installation This section provides an installation procedure for each Mud Mount Kit. The procedure for the MMK-1000L starts below and the "WMKM-1000L Procedure" starts on page 4. MMK-1000L Procedure The procedure in this section provides the necessary steps for the assembly of the MMK-1000L to either the PMK-1000L or BB-1000L. It is assumed that the PMK-1000L or BB-1000L has been secured to the stud according to the procedures in the latest revisions of their respective Installation Guides (Doc. [. . . ] 6062 Mud Mount Kits: MMK-1000L & WMKM-1000L · 3 Mud Mount Kits Crestron MMK-1000L & WMKM-1000L clearance holes in the PMK-1000L (or BB-1000L) and are secured in the extruded holes of the fastener plates. Verify that the mud ring plate is level. NOTE: Do not over tighten screws. Use a #2 Phillips screwdriver and tighten the drywall screws by hand so that they slightly dimple into the holes in the mud ring plate. 10. When dry, the Series 1000 touchpanel can be installed using the four tapped holes in the PMK-1000L. Refer to the latest revision of the Series 1000 Operations Guide (Doc. 5813) for details. WMKM-1000L Procedure The procedure in this section provides the necessary steps for the assembly and installation of the WMKM-1000L into a wall. The only tools or materials required and not supplied are a drywall saw or equivalent, a level, four standard drywall screws, #2 Phillips screwdriver, and tools/material to apply drywall joint compound. Insert the two pins on one fastener plate into the top two outer holes on the mounting plate, as shown in the illustration after this step. PUSH-ON FASTENER QTY. 4 Create the Fastener/Mounting Plate Assembly MOUNTING PLATE QTY. 1 FASTENER PLATE QTY. 2 4 · Mud Mount Kits: MMK-1000L & WMKM-1000L Installation Guide ­ DOC. 6062 Crestron MMK-1000L & WMKM-1000L 2. Mud Mount Kits Slide a push-on fastener over each pin on the top fastener plate. Slide them on enough to keep the fastener plate and mounting plate as one fastener/mounting plate assembly. Use the second fastener plate and repeat steps 1 and 2 on the lower part of the mounting plate. Locate an area on the wall that is free of miscellaneous wiring and studs. Make a small hole near the middle of the designated site; verify that the location is suitable. 3. Use the drywall saw or equivalent to produce a level, square cutout in the drywall that measures 4½ inches wide (114 mm) x 4½ inches high (114 mm). Insert the symmetrical mud ring plate into the opening, as shown in the illustration after this step. 7. Insert the Mud Ring Plate into the Opening MUD RING DRYWALL CUTOUT: 412 in WIDE x 412 in HIGH (114 mm WIDE x 114 mm HIGH) 8. Carefully pass the fastener/mounting plate assembly through the opening and rest the assembly against the interior surface of the Installation Guide ­ DOC. 6062 Mud Mount Kits: MMK-1000L & WMKM-1000L · 5 Mud Mount Kits Crestron MMK-1000L & WMKM-1000L drywall. Verify that the fastener plates are between the mounting plate and the drywall. When the fastener/mounting plate assembly is in position, bend the top two flanges of the mud ring upward (approximately 90 degrees) and the bottom two flanges downward (approximately 90 degrees). Refer to the illustration after this step. NOTE: Fastener/mounting plate assembly will have slight play; this is normal. It allows for minor adjustments to the touchpanel during installation. Bend Flanges BEND THESE TABS UP APPROX. [. . . ] To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ]