User manual CRESTRON LEPB-4

[. . . ] DESCRIPTION The Power Extender will emulate the characteristics of the dimmer that it is connected to in terms of dimming range and resolution. Compatibility · Box Mounted Dimmers ­ Must use a 120V, 600W Incandescent version of the following families: Illumatech, Mural, True Touch, Toggle Touch, Touch Point, and Home Controls · Monet Installations ­ Must use Monet Magnetic Low-Voltage (requires a Neutral wire). · Architectural Systems ­ All families NOTE: For dimmers that include a Neutral wire (such as some scene capable dimmers), the dimmer Neutral wire must be connected. [. . . ] Activating the air gap on the dimmer will cause the PE300 to turn its controlled Load OFF. CAUTION: The Power Extender will still remain powered, but it will not activate the load. The PE300 has an air gap relay built in, therefore, the ballasts will be disconnected by an air gap when the dimmer is OFF or the air gap control on the dimmer is activated. Table 1 ­ LED Indicators LED Meaning Physical Location Color State Relay LED 1 Red If load is connected, LED ON Power LED 2 Green If there is internal power, LED ON For more information go to www. leviton. com INSTALLATION INSTRUCTIONS DI-000-PE300-00A OUTPUTS Dimming Control: The GRAY and VIOLET wires provide a control voltage (current sink) that DIMS the ballasts. WIRING All wires type: 105°C AWM, 600V Table 2 ­ Wiring Designators Signal Name Color Black White Green Red White/Red 2 Blue Violet Gray Violet Gray Gauge 18AWG 18AWG 12AWG 18AWG 18AWG 12AWG 18AWG 18AWG 18 AWG 18 AWG From bottom opening Line (for power supply) Neutral (for power supply) Ground Dimmer input Dimmer return Relay contacts ­ Load Dim (To Ballast) Return (To Ballast) WARNING: TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS. WARNING: IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED ELECTRICIAN. NOTE: The Power Pack must be installed in a properly grounded metal 4" (10. 2 cm) outlet box. Depending on the application and the number of connections, more space may be needed. There are two wiring ports on the Power Pack, one for high-voltage (Line) wires and one for low-voltage wires. The high-voltage wires exit out of the bottom, and the low-voltage wires exit out of the side. Refer to Table 2 for wire designations. From side opening Dim (To Ballast) Return (To Ballast) LIMITED 2 YEAR WARRANTY AND EXCLUSIONS Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for two years from the purchase date. Leviton's only obligation is to correct such defects by repair or replacement, at its option, if within such two year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co. , Inc. , Att: Quality Assurance Department, 5925 Little Neck Parkway, Little Neck, New York 11362-2591 (In Canada send to Leviton Mfg. of Canada Ltd. , 165 Hymus Blvd. , Point Claire, (Quebec), Canada H9R 1E9). This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to two years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise. The dimmer can be connected to the same line as the PE300 power wires, or it can be connected to a separate line. [. . . ] Low-Voltage Wiring (side wiring port): Connect lead wires per WIRING DIAGRAM as follows: Using low-voltage wires exiting the Power Pack, twist strands tightly together and, with lowvoltage device conductors, push firmly into appropriate wire connector. Screw connectors on clockwise making sure that no bare conductor shows below the wire connectors. Secure each connector with electrical tape. Figure 1 ­ Controls · The Power Extender is not powered (Green LED OFF) - Circuit breaker is OFF. [. . . ]