User manual CRESTRON IRP2

[. . . ] Apply transparent silicon adhesive (not supplied) to the flat side of the IRP2 or use the supplied transparent tape. CAUTION: Test the silicon adhesive on a non-visible area to confirm that it will not damage material or equipment. Affix the IRP2 in the center of the IR sensor window on the front panel of the controlled component. Use a piece of non-damaging tape to hold the IRP2 in position while the silicon adhesive cures. [. . . ] Placement of the IRP2 on surfaces just above or below the IR sensor window, as shown in the following illustrations, may provide a more pleasing aesthetic appearance. However, be sure to position the IRP2 shell so that the edge of the component does not block the IR signal. NOTE: Placing the IRP2 shell on a cabinet door may result in interruption of the IR signal if the door is opened. Possible mounting locations of the IRP2 shell include being attached to a shelf directly below or above the IR sensor window. Front View Side View Connect the IRP2 Insert the two-pin connector of the IRP2 into an infrared - serial output port of the control system as shown in the following illustration. 4 · Infrared Emitter Installation Guide ­ DOC. 8168A Crestron IRP2 Infrared Emitter NOTE: The white-traced wire connects to the pin labeled S. Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. For assistance in your local time zone, refer to the Crestron website (http://www. crestron. com) for a listing of Crestron worldwide offices. You can also log onto the online help section of the Crestron website to ask questions about Crestron products. First-time users will need to establish a user account to fully benefit from all available features. Installation Guide - DOC. 8168A Infrared Emitter · 5 Infrared Emitter Crestron IRP2 As of the date of manufacture, the IRP2 has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Future Updates As Crestron improves functions, adds new features, and extends the capabilities of this product, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Check the Crestron website periodically for manual update availability and its relevance. Updates are identified as an "Addendum" in the Download column. 6 · Infrared Emitter Installation Guide ­ DOC. 8168A Crestron IRP2 Infrared Emitter Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ] In no event shall CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for any claim made by a third party or made by the purchaser for a third party. CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. [. . . ]