User manual CRESTRON IO APAD

[. . . ] Crestron APAD Wall Mount LCD Controller Operations & Installation Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2006 Crestron Electronics, Inc. Crestron APAD Wall Mount LCD Controller Contents Wall Mount LCD Controller: APAD 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You can choose to load the project at this time (refer to "Uploading and Upgrading" on page 17), or follow the screen instruction and press any button to enter the Setup Mode. If the APAD project has already been loaded, the MAIN MENU for configuring the APAD, shown to the left, appears when any button is pressed and held (approximately five seconds) when power is applied. Note that holding any of the soft buttons for more than 10 seconds while going into setup mode will reset the brightness and contrast to their default levels. The MAIN MENU displays three soft button choices: About, Setup, and Save and Exit. MAIN MENU ABOUT Screen Selecting About displays an information screen that shows the firmware, project name, and version number. Selecting Setup displays the Setup screen (Refer to "Setup Mode, " below) that provides all the parameters that are used to configure the APAD. The Save and Exit selection is used after performing all setup functions to save the configuration and exit to normal operation. Load in Progress Screen If you choose to load the project at this time, the screen displays a progress bar as the project is loaded (shown to the left). Setup Mode Screen Setup Mode Setup Mode can be entered from the Main Menu, as stated above, or, if the APAD has not yet been installed, by pressing and holding any button when power is applied. If the unit is installed and power is already applied, the easiest method is to remove the bezel, press and hold any button, and press the Reset button; the unit immediately enters Setup Mode. In the Setup Mode, use the Nav Wheel to scroll through the menu options, and then press the soft button to the right to select the option. The following paragraphs describe each of the setup options in the order listed in the menu. Cresnet ID Screen Cresnet ID Use the Nav Wheel to select the desired ID number, from 03 to FE, in least significant digit steps (e. g. , 03, 04, 05), or use the << and >> soft buttons to change the number in most significant digit steps (e. g. , 03, 13, 23). Press the Default soft button to select the default ID value (2E), press the Ok soft button to accept the selection and return to the Setup Mode screen. 12 · Wall Mount LCD Controller: APAD Operations & Installation Guide ­ DOC. 6455 Crestron APAD Wall Mount LCD Controller LCD Brightness LCD Brightness Use the Nav Wheel to select the desired brightness percentage value, from 01 to 99, in single digit steps (01, 02, 03, etc. ), or use the << and >> soft buttons to change the number in most significant digit steps (10, 20, 30, etc. ). Note that holding any of the soft buttons for more than 10 seconds while going into setup mode will reset the brightness to the default (22%). Press the Default soft button to return to the default setting; press Ok to accept the new setting and return to the Setup Mode screen. Screen Invert Screen Invert Use the soft buttons to turn screen inversion on or off. ("Off" is normal appearance ­ white text on black screen. "On" is inverted appearance ­ black text on white screen. ) Press the Default soft button to return to the default setting; press Ok to accept the new setting and return to the Setup Mode screen. LCD Contrast LCD Contrast Use the Nav Wheel to select the desired LCD contrast percentage value, from 01 to 99, in single-digit steps (01, 02, 03, etc. ), or use the << and >> soft buttons to change the number in most significant digit steps (10, 20, 30, etc. ). Note that two contrast settings are required: one for invert on, and one for invert off. Note that holding any of the soft buttons for more than 10 seconds while going into setup mode will reset the contrast to the defaults (non-inverted contrast 72%; inverted contrast 66%). Press the Default soft button to return to the default setting; press Ok to accept the new setting and return to the Setup Mode screen. Key Backlight Key Backlight Use the Nav Wheel to select the desired key backlight percentage value, from 01 to 99, in single-digit steps (01, 02, 03, etc. ), or use the << and >> soft buttons to change the number in most significant digit steps (10, 20, 30, etc. ). Press the Default soft button to return to the default setting (30%); press Ok to accept the new setting and return to the Setup Mode screen. Standby Standby Use the Nav Wheel to select the desired standby minutes, from 0 to 120, in singleminute increments, or use the << and >> soft buttons to change the number in tenminute increments (10, 20, 30, etc. ). Press the Default soft button to return to the default setting (10 minutes); press Ok to accept the new setting and return to the Setup Mode screen. Key Click Key Click Use the ON and OFF soft buttons to turn the Key Click feature on and off (default is off). Press the Default soft button to return to the default setting; press Ok to accept the new setting and return to the Setup Mode screen. Operations & Installation Guide ­ DOC. 6455 Wall Mount LCD Controller: APAD · 13 Wall Mount LCD Controller Crestron APAD Programming Software Have a question or comment about Crestron software? [. . . ] Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. [. . . ]