User manual CRESTRON HBK-6000 SMK-6000

[. . . ] The SMK-6000 should not be used in combination with the TPS-XVGA RGB Graphics Card, as it does not accommodate the size and bend-radius of a typical off-the-shelf RGBHV cable. Instead, the TPS-XVGA-BV RGB Graphics Card w/Balanced Video should be used. The TPS-XVGA-BV includes a special Triamese cable, which is compact and flexible enough to use with the SMK-6000. Supplied Hardware The hardware supplied in the kits is listed in the following table. Supplied Hardware of the HBK-6000 and SMK-6000 Hatchback and Swivel Mount Kits HBK-6000 One (1) Metal Bracket One (1) Plastic Cover Four (4) Screws 4-40 X 3/16 inch SMK-6000* One (1) Swivel Mount Assembly One (1) Metal Bracket One (1) Metal Plate One (1) Plastic Cover Sixteen (16) Screws (4) 4-40 X 3/16-inch (4) 6-32 X 1/4-inch (4) 8-32 X 5/8-inch (4) 8-32 X 1-inch * The SMK-6000 mounting kit includes a template for preparing the mounting surface. Installation Guide ­ DOC. 6111 Hatchback and Swivel Mount Kits: HBK-6000 & SMK-6000 · 1 Hatch Back and Swivel Mount Kits Crestron HBK-6000 & SMK-6000 Installation This section provides an installation procedure for each kit. [. . . ] 5. Hatch Back and Swivel Mount Kits Place the touchpanel face down on a padded surface to prevent damage to the display screen. Refer to the following illustration and remove the six screws from the bottom rear of the touchpanel that correspond to the mounting holes (A) in the metal bracket of the kit. SMK-6000 Swivel Mount Kit Assembly Diagram 6. Place the metal bracket on the touchpanel base (mounting holes should align, touchpanel feet should protrude through openings provided, and standoff posts for the rear cover should point toward the touchpanel). Secure the metal bracket to the touchpanel using the six screws removed in step 5. Route the cables from the interface box up through the Metal Plate, through the mounting surface, and through the Swivel Assembly, then through the area of the bracket shown in the figure, and connect to the appropriate touchpanel ports. Being careful to avoid damage to the cables, attach the Swivel Assembly to the Metal Bracket, using the supplied four #6-32 X 1/4 inch screws B through the holes in the swivel assembly into the standoff posts on the bracket. Make certain the cables are not twisted or crimped and have sufficient slack at the port connections before fully tightening the screws. Hatchback and Swivel Mount Kits: HBK-6000 & SMK-6000 · 3 7. 8. Installation Guide ­ DOC. 6111 Hatch Back and Swivel Mount Kits 9. Crestron HBK-6000 & SMK-6000 Make certain tab C is positioned to the front of the swivel assembly, and that it is directly opposite bent tab E, and place the touchpanel and swivel mount assembly down on the Mounting Surface. 10. Hold the Metal Plate in position under the mounting surface and secure the assembly in place using the #8-32 screws F provided (use the 5/8-inch screws for surfaces 3/4-inch to 1 1/8-inches thick; use the 1-inch screws for surfaces 1 1/8 to 1 3/8 inches thick). Refer to the following illustration, put the plastic cover in position and secure to the metal bracket using the four #4-40 X 3/16-inch screws supplied. SMK-6000 Swivel Mount Kit Rear Cover Assembly Screws (4) Plastic Cover Metal Bracket Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. For assistance in your local time zone, refer to the Crestron website (www. crestron. com) for a listing of Crestron worldwide offices. You can also log onto the online section of the Crestron website (www. crestron. com) to ask questions about Crestron products. First-time users will need to establish a user account to fully benefit from all available features. As of the date of manufacture, the HBK-6000 and SMK-6000 have been tested and found to comply with specifications for CE marking. Future Updates As Crestron adds improvements to the HBK-6000 or SMK-6000, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Check the Crestron website (www. crestron. com) periodically for manual update availability and its relevance. Updates are available from the Download | Product Manuals section and are identified as an "Addendum" in the Download column. 4 · Hatchback and Swivel Mount Kits: HBK-6000 & SMK-6000 Installation Guide ­ DOC. 6111 Crestron HBK-6000 & SMK-6000 Hatch Back and Swivel Mount Kits Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. [. . . ] CRESTRON is not liable for any claim made by a third party or made by the purchaser for a third party. CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. [. . . ]